934. If an element is subjected to the state of stress shown in Fig. P-934, find the principal stresses and the maximum shearing stresses. Also determine the stress components on planes whose normals are at 45° and 135° with the X axis. Show all results on complete sketches of the appropriate elements. 60 MPa 40 MPa 60 MPa X- 40 MPa Figure P-934.

934. If an element is subjected to the state of stress shown in Fig. P-934, find the principal stresses and the maximum shearing stresses. Also determine the stress components on planes whose normals are at 45° and 135° with the X axis. Show all results on complete sketches of the appropriate elements. 60 MPa 40 MPa 60 MPa X- 40 MPa Figure P-934.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
For the stresses of plane stress state is ?? = −8 ??? , ?? = 7 ??? and??? = −6 ???Draw a Mohr’s circle diagram.Draw stress element for the given stressesFind the principal normal and shear stresses, and determine the anglefrom the x axis to ?1Draw the stress element for the principle stress.Using stress transformation, find the principle stresses and the angle of ?1Determine the stress transformation for the angle ∅ = 25° #Answer all in detail
Direct stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm?. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?
In a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} = 80MPa , Ty = 40 MPa . What is the maximum shear stress (in MPa) at the point?
The diagram below shows Mohr’s circle for a point in a physicalobject that is subjected to plane stress.(a) Determine the stresses σ x, σ y, and τ xy, and show them on astress element.(b) Determine the principal stresses and the maximum in-planeshear stress acting at the point, and show these stresses on anappropriate sketch
Using Mohr's circle on each case, determine a)The principal stresses and maximun shear stress. Show all results on sketches of properly oriented elements b)Is there the invariance of normal stresses in each case?
For the plane stress sigma x = -8MPa, sigma y = 7MPa, tow xy= 6MPa cw, draw a Mohr’s circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the axis to . Draw stress elements
At a point on the free surface of a stressed body, thenormal stresses are 20 ksi (T) on a vertical plane and 30 ksi (C) ona horizontal plane. An unknown negative shear stress exists on thevertical plane. The absolute maximum shear stress at the point hasa magnitude of 32 ksi. Determine the principal stresses and theshear stress on the vertical plane at the point.
At a certain point in a stressed body, the principal stresses are fx=80 MPa and fy=-40MPa. Determine the normal and shearing stresses on the plane whose normal is at +30 degrees with the X-axis.
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
Assume the plane stress element shown in Fig. E3-a represents the stress a geosynthetic membrane used in a mechanically stabilized earth wall. If the reference state of stress for this element results in the Mohr’s circle plot shown in Fig. E3-b, determine: The principal stresses. The principal directions (angles to the principal planes). The maximum in-plane shear stress. It is known that the seam, which is rotated 45 deg from the vertical as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated.