A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 7.5 in., and the load applied to each pulley is P = 58 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. A B, D L L /3 /3 /3

A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 7.5 in., and the load applied to each pulley is P = 58 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. A B, D L L /3 /3 /3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 0.400 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in., and the load applied to each pulley is P = 51 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft.
A horizontal beam is supported by an inclined strut and carries a load of 15 kN at joint AD CBD in the figure. The strut, which consists of two bars each of thickness 40 mm, is connected tothe beam by a rivet passing through the three bars meeting at joint. The allowable shear Cstress and bearing stress are all, z =60 MPa and =120 MPa, respectively.a) Determine the required diameter of the rivet at the hinge that carries safely by the given Csystem.b) If the diameter rivet used on the support is 20 mm check whether this rivet diameter is Asufficient for the given system.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do = 200 mm. (E = 154 GPa)
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Calculate the allowable force in rod (1).
Q.1 A structure is supported by braces each of which transfersa load P = 160 kips to the base of a column as shown infigure. A cap plate at the bottom of the brace distributesthe load P to four flange plates through a pin to twogusset plates. Diameter of Pin and thickness of flangeplate and gusset plate are provided in figure. Determine(a) The average shear stress in the pin.(b) The average bearing stress between the flange plates andthe pin.(c) The normal axial stress in gusset plate. Assume thatgusset plate is 4 inch wide. Note: Please answer the section c as well
The simply–supported beam is loaded as shown. Use P = 8 kN and Q = 12 kN. Draw the shear and moment diagram. Plot the flexural stress distribution at point of maximum moment.
The double-collar bearing is subjected to an axial force P = 16 kN. Assuming that collar A supports 0.75P and collar B supports 0.25P, both with a uniform distribution of pressure, determine the smallest torque M that must beapplied to overcome friction. Take μs = 0.2 for both collars.
The cargo box as shown weighs W = 1200 lb. The force P = 800 lb is just sufficient to lift the box off the floor. The 2-D concurrent force system of the joint O is shown as well. Using the equilibrium equations: ∑ ???= 0 ; ∑ ???= 0, 1) Determine the tension force in the cable T;2) Determine the corresponding value of β
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?