A 0.800-m-diameter vat of liquid is 2.70 m deep. The pressure at the bottom of the vat is 1.50 atm. Part A What is the mass of the liquid in the vat? Express your answer with the appropriate units. ? Value Units m =

A 0.800-m-diameter vat of liquid is 2.70 m deep. The pressure at the bottom of the vat is 1.50 atm. Part A What is the mass of the liquid in the vat? Express your answer with the appropriate units. ? Value Units m =

Name: A 0.800-m-diameter vat of liquid is 2.70 m deep.The pressure at the b
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: A 0.800-m-diameter vat of liquid is 2.70 m deep.The pressure at the bottom of the vat is 1.50 atm.Part AWhat is the mass of the liquid in the vat?Express your answer with the appropriate units.HÀValueUnitsm =SubmitPrevious Answers Request AnswerX In

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter11: Fluid Statics

Section: Chapter Questions

Problem 34PE: A submarine is stranded on the bottom of the ocean with its hatch 25.0 m below the surface....

See similar textbooks

Similar questions

Concrete is pumped from a cement mixer to the place it is being laid, instead of being carried in wheelbarrows. The flow rate is 200.0 L/min through a 50.0-m-long, 8.00-cm-diameter hose, and the pressure at the pump is 8.00106 N/m2. Verify that the flow of concrete is laminar taking concrete's viscosity to be 48.0 (N/m2) s, and given its density is 2300 kg/m3.
A tank with a flat bottom of area A and vertical sides is filled to a depth h with water. The pressure is P0 at the top surface. (a) What is the absolute pressure at the bottom of the tank? (b) Suppose an object of mass M and density less than the density of water is placed into the tank and floats. No water overflows. What is the resulting increase in pressure at the bottom of the tank?
An oil gusher shoots crude oil 25.0 m into the air through a pipe with a 0.100-m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the gauge pressure at the entrance of the 50.0-m-long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) s (or 1.00 Pa s). Note that you must take into account the pressure due to the 50.0-m column of oil in the pipe.
Calculate the Reynolds numbers for the flow of water through (a) a nozzle with a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when the nozzle is attached to the hose. The flow rate through hose and nozzle is 0.500 us. Can the flow in either possibly be laminar?
Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.400 m2, and the pipe gradually widens so that its area near the ground is 0.800 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe?
Unreasonable Results A fairly large garden hose has an internal radius of 0.600 cm and a length of 23.0 m. The nozzle-less horizontal hose is attached to a faucet, and it delivers 50.0 L/S. (a) What water pressure is supplied by the faucet? (b) What is unreasonable about this pressure? (c) What is unreasonable about the premise? (d) What is the Reynolds number for the given flow? (Take the viscosity of water as 1.005103(N/m2)s .)
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate the new flow rate for the following changes with all other factors remaining the same as in the original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid with 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube is used with a radius 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half the length, and the pressure difference is increased by a factor of 1.50.
Find the gauge and absolute pressures in the balloon and peanut jar shown in Figure 11.16, assuming the manometer connected to the balloon uses water whereas the manometer connected to the jar contains mercury. Express in units of centimeters of water for the balloon and millimeters of mercury for the jar, taking h=0.0500 m for each. Figure 11.16 An open-tube manometer has one side open to the atmosphere. (a) Fluid depth must be the same on both sides, or the pressure each side exerts at the bottom will be unequal and there will be flow from the deeper side. (b) A positive gauge pressure Pg=hg transmitted to one side of the manometer can support a column of fluid of height h. (c) Similarly, atmospheric pressure is greater than a negative gauge pressure Pg by an amount hg .The jar's rigidity prevents atmospheric pressure from being transmitted to the peanuts.
How tall must a water-filled manometer be to measure blood pressures as high as 300 mm Hg?
Gasoline is piped underground from refineries to major users. The flow rate is 3.00102 m3/s (about 500 gal/ min), the viscosity of gasoline is 1.00103 (N/m2) s, and its density is 680 kg/m3. (a) What minimum diameter must the pipe have if the Reynolds number is to be less than 2000? (b) What pressure difference must be maintained along each kilometer of the pipe to maintain this flow rate?
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
Pascal’s Principle and Hydraulics 59. How much pressure is transmitted in the hydraulic system considered in Example 14.3? Express your answer in atmospheres.