A 1" diameter line shaft, which is supported by frictionless pulleys at the ends, carries 2 pulleys. The 10" diameter driver pulley is driven in a counter-clockwise direction, and its belt tensions are 25 lbs and 56 lbs. The 2" diameter driven pulley has one of its belt tensions measured at 30 lbs. Calculate the missing belt tension.

A 1" diameter line shaft, which is supported by frictionless pulleys at the ends, carries 2 pulleys. The 10" diameter driver pulley is driven in a counter-clockwise direction, and its belt tensions are 25 lbs and 56 lbs. The 2" diameter driven pulley has one of its belt tensions measured at 30 lbs. Calculate the missing belt tension.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.60P: The force P applied to the brake handle enables the band brake to reduce the angular speed of a...

See similar textbooks

Similar questions

The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
The figure below shows a stored shaft where bearing A is a cylindrical bearing and bearing O is a spherical roller bearing. There are two disks shrunk onto the shaft. Their diameters are 300 and 600 mm. a) Determine the force P such that the shaft rotates at a constant speed. b) Find the diameter of the shaft if σ_till is 100 MPa.
A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
A pulley 610 mm diameter is driven at 300 revs/min by a belt, the tensions in the tight and slack sides of the belt being 670 N and 270 N. Find the power transmitted.
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 100 kg at the crank pin, and the reciprocating masses per cylinder to 200 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the magnitude of the balancing mass on the right most wheel. Select one: A. 55.32 kg B. 322.3 kg C. 225.3 kg D. 115.3 kg
ANSWER ASAP The worm gear rotating at 1250 rpm drives a worm wheel and whose velocity ratio is 12 to 1. A driving motor with 12 hp is used to supply the worm with worm pitch gear diameter of 3.5 in. Find the tangential force on the gear.
A shaft has three eccentrics of mass 1kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20 mm, 30 mm, and 20 mm and their angular positions are 120 degree apart. Find the amount of out-of-balance force and couple at 600 rpm. If the shaft is balances by adding two masses at a radius of 70 mm and at a distance of 100 mm from the central plane of the middle eccentrics, find the amount of masses and their angular positions. (Use graphical method for solution)
A tractor is now drafted in to move the blo ck. The weight of the tractor is equally distributed over all four wheels and it pulls on the blo ck via a rope with tension T. The back wheels have a diameter of 1.6m and the front wheelshave a diameter of 80cm. The tractor motor generates a torque of τ on each of its back wheels that have radii Rb and masses mb. The front wheels of the tractor are smaller than the back wheels and have radii Rf and masses mf. Both sets of wheels can b e treated as uniform solid disks with moment ofinertia I = 1/2mR2. The mass of the tractor body, without the wheels, is M. If the wheels don't slip, show that the tractor can accelerate the block with an acceleration of (see image)
The block-type parking brake shown in the figure has a width of 49 mm and an average friction coefficient of 0.32. Calculate the maximum pressure and braking moment on the shoe to provide a thrust of 419 N in the anti-clockwise system?
The reaction forces applied by the unbalanced loads on the shaft to the A and B bearings,FA = 3i N and FB = 4i N. If the shaft rotates at 300 rpm, specify the magnitude of the unbalanced loads (in kg.mm) and find their angular positions. Distances are given with a= 200 mm and b = 300 mm. (Note that the angles θ1 and θ2 are not known.)
A ladder of length 2L and mass M is positioned on level ground leaning against a wall such that the angle between the ladder and the horizontal is @. The coefficient of static friction between the ladder and the wall and between the ladder and the ground is jistatic = 0.66. The centre of mass of the ladder is halfway along it. For the ladder to be in mechanical equilibrium: Consider torques about the centre of the ladder. In which direction (into or out of the page) does the torque due to each of the 5 forces force act?Write down an equation for the sum of the torques about the centre or mass of the ladder and then use your equation for the torques to derive an expression for tan o in terms of the magnitudes of the forces acting