A 12-stage impulse voltage generator has a capacitor C. The wave front resistance equal to 0.6kΩ and wave tail resistance 7019Ω. If the wave front and wave tail times of the impulse wave are 2 μs and 0.06 ms respectively. Calculate (i) the capacitance of each capacitor in the generator and (ii) the capacitance of the load capacitor (C2)?

A 12-stage impulse voltage generator has a capacitor C. The wave front resistance equal to 0.6kΩ and wave tail resistance 7019Ω. If the wave front and wave tail times of the impulse wave are 2 μs and 0.06 ms respectively. Calculate (i) the capacitance of each capacitor in the generator and (ii) the capacitance of the load capacitor (C2)?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 2PP: Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the...

See similar textbooks

Similar questions

Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
An impulse generator has 8 stages, each having a capacitance of 1.2 μF and 167 KV. If it has to produce a 1/50 (μs) waveform across a load capacitor of 15000 PF, (1) what is its maximum discharge energy, and (2) calculate the regulation? If• t1=3R1C1C2 / (C1+ C 2), and t2=0.7(R1+R2) (C1+ C2) and use exact method
Q/ a. Draw a 5-stage Marx impulse generator circuit showing the voltages of all points. Also, show the capacitor’s voltages and their polarities if the generator is supplied by a DC voltage source of 127 kV. b. Explain how it works. c. What is the output testing voltage if each stage has a voltage drop of 7 kV? d. In the lab, if the first spark gap is not small enough to start the avalanche (the breakdown of all gaps), and you cannot make it smaller, what could you do to fix this problem?
POWER SİSTEMS high voltage technique it is possible to measure pulsed (AND ANSWER THE SAME QUESTION FOR AC AND DC ) high voltages with the help of two spheres of equal radius placed on the same axis. In which case the approximate impulse,AC AND DC voltage value that can be measured with such a system with diameters of 500 mm and known spacing between them is 2.5 cm, is given correctly. (Ambient conditions are neglected and take Ed = 30 kV / cm2 k = 0.9) a) 68,65114 kV b) 81.30081 kv c) 97,08737 kv d) 65,35947 kv e) 57.48835 kv f) 46.21612 kv PLEASE ANSWER THE SAME QUESTION FOR DC HİGH VOLTAGE AND AC HİGH VOLTAGE WHAT THE DIFFERENCE BETWEEN THEM
A 8-stage impulse voltage generator is connected to a test object of load capacitance of 5000pF with wave front resistance equal to 700 Ω. If the wave tail and wave front times of the impulse wave are 50 μs and 1500 ns respectively. Calculate (i) wave tail resistance value and (ii) the capacitance of the impulse generator?
Question 1. An industrial load consisting of a set of induction motors connected to a 220 V, 60 Hz single phase source consumes 50 kW with a back power factor of 0.8. The power factor will be increased back to 0.95 by connecting a set of capacitors in parallel. For this, calculate the VA value that the connected capacitor will provide.
a single-stage impluse generator has a 0.01 micro farad capacitor. the wave front and wave tail resistances are 800 ohm and 3000 ohm respectively. if the load capacitor 1200 pico farad , find the front and tail times of the impluse wave produced.
L:57) A coil having an inductance of 0.01 H and resistance of 5 ohm is connected in parallel with a capacitance of 100 microfarad. If the supply voltage is 220 V and its frequency is 60 Hz, calculate: The reactive power absorbed by the coil The reactive power generated by the capacitor The active power absorbed by the coil.
A superheterodyne receiver is to tune the range 88.1MHz to 107.1MHz. The RF circuit inductance is 1μH. Low-side injection is used.a. Calculate the minimum capacitance of the variable capacitor in the RF circuitb. Calculate the RF circuit capacitance tuning ratio c. If the receiver has a single converter stage and IF of 800kHz, calculate the capacitance tuning ratio of the local oscillator d. If the maximum capacitance of the variable capacitor of the local oscillator is 0.2pF, calculate the minimum capacitance e. If the receiver has a single converter stage and IF of 800kHz, calculate the image frequency of 103.7MHzf. Calculate the IFRR (in dB) of (e) if Q of the preselector is 50 g. To increase the IFRR of (e) to 40dB, double conversion is used. What must be the frequency of the 1st IF?
A coil of inductance 318.3 mH and negligible resistance is connected in series with a 200 resistor to a 240V, 50 Hz supply. Calculate the inductive reactance of the coil, the impedance of the circuit, the current in the circuit, the p.d. across each component, and the circuit phase angle.
The circuit has a switch that closes at t=0. Resistor R = 2.6ohms. L=0.1H, C= 4F while Vs= 24 volts Write down coefficients of the characteristic equation of the transient behavior of this circuit S^2 + _ s+ _=0 fill in the blanks “_”
An inductor L is connected in parallel to the series combination of capacitor C and resistor R. If L = 0.02122 H, C = 0.000421 F and R = 5 Ω, the impressed voltage E = 120 volts AC. Find the following: a. Circuit Diagram, total impedance, total current. b. Determine the frequency at which the inductive reactance is equal to capacitive reactance. c. Determine the voltage drop across the capacitor and the Quality Factor Q.