:)A 1200 N uniform boom at o = 65.0 degrees to the horizontal is supported by a cable at an angle 0 = 25.0 degrees to the horizontal. The boom is pivoted at the bottom, and an object of weight m= 2.00E3 N hangs from its top. Find (a) the tension in the support cable and (b) the components of the force exerted by the floor on the boom (through the hinge).

:)A 1200 N uniform boom at o = 65.0 degrees to the horizontal is supported by a cable at an angle 0 = 25.0 degrees to the horizontal. The boom is pivoted at the bottom, and an object of weight m= 2.00E3 N hangs from its top. Find (a) the tension in the support cable and (b) the components of the force exerted by the floor on the boom (through the hinge).

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

The uniform ladder of weight W is raised slowly by applying a vertical force P to the rope at A. Show that P is independent of the angle .
The uniform bar of weight W is held in equilibrium by the couple C0. Find C0 in terms of W, L, and .
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
Compute the tension TAE in Sample Problem 5.7 using one scalar equilibrium equation.
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
A uniform horizontal beam with a length of 1.7 m and a weight of 200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 35.0° with the horizontal. If a crate of mass (M) 87 kg hanged 1.7 m from the wall, find the tension in the cable, as well as the magnitude and direction of the resultant force exerted by the wall on the beam.
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at the center of the beam, what is the tension in the right rope?