Question in the attachment Above: This shows the inside of a rheostat (variableresistor). One wire is attached to and end, and the otherto the slide. As you move the slide, more wire is added,and the resistance goes up. This is how a light dimmerworks- you turn a dial, the resistance increases, and thebulb dims. A 13.8 V battery is connected in series to a 9.46 µF capacitor, a 1.79 mH resistanceless coil, a rheostat (variable resistor- see right photograph at the bottom of thediagrams for this assignment) ) and an open switch. At t = 0, the switch is closed. Find the value of R, in Q, that will make this circuit critically damped.

Answered: Image /qna-images/answer/94dcdb02-7061-4204-b3e1-15b77e834786.jpg

A 13.8 V battery is connected in series to a 9.46 µF capacitor, a 1.79 mH resistanceless coil, a rheostat (variable resistor- see right photograph at the bottom of the diagrams for this assignment) ) and an open switch. At t = 0, the switch is closed. Find the value of R, in Q, that will make this circuit critically damped.

A 13.8 V battery is connected in series to a 9.46 µF capacitor, a 1.79 mH resistanceless coil, a rheostat (variable resistor- see right photograph at the bottom of the diagrams for this assignment) ) and an open switch. At t = 0, the switch is closed. Find the value of R, in Q, that will make this circuit critically damped.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

As displayed in attachment figure and LC circuit can be modeled by the following system of differential equations as attachment. Where L = inductance (H), t = time (s), i = current (A), and C = capacitance (F). Assuming that a solution is of the form = Ij sin (wt), determine the eigenvalues and eigenvectors for this system using Faddeev-Leverrier Method and Power Method with L = 1 H and C = 0.25 C. Draw the network, illustrating how the currents oscillate in their primary nodes. Assume initial value for power method.
For the circuit below with the switch closed and then opening at t=0, and R1= 3Ω, R2= 7Ω, C = 0.2H, ig = 8A, vs = 2v, calculate the initial condition. Develop the differential equation for the solution for t > 0. Calculate the current ia(t) for all times.
Given the circuit below with the switch closed for a long time, then opening at t=0, and with the values R1=129KΩ, R2=128KΩ, R3=103KΩ, calculate the time constant, τ, for the capacitor voltage solution for at t >0.
The circuit elements in the circuit L=50 mH, and C=0.2 μF. The initial inductor current is−45 mA and the initial capacitor voltage is 15 V. The resistance is increased to250 Ω. Find the expression for v(t) for t≥0.
It is known that the switch shown, T, is initially open and then it closed in theinstant t = 0. If it is assumed that the circuit has reached the stable state before the action of said switch:1.1. Determine the value of the capacitance of capacitor C so that the given circuit is critically damped.1.2. For the damping conditions of the previous part, find the expression for the current, i (t), forall t> 0.
The switch in Fig. is moved from A to B att 0 after being at For a long time. This places the two capacitors in series, thus allowing equal and opposite dc voltages to be trapped on the capacitors. (a) Determine v1(0-), v2(0-), and vR(0-). (b) Find v1(0+). v2(0+), and vR(0+). (c) Determine the time constant of VR(t). (d) Find vR(t), t> 0. (e) Find i(t). () Find vi(t) and v2(t) from i(t) and the initial values. (g) Show that the stored energy at t = plus the total energy dissipated in the 20 k resistor is equal to the energy stored in the capacitors at t=0
The mathematical models of some continuous time systems are given above. x(t) is the input signal of the system, and y(t) is the output signal of the system. Which of the following systems is linear and which is nonlinear? For linear systems, write "linear" in the space next to the option. For non-linear systems, write "non-linear" in the space next to the option.
A VOLTAGE V=10 VDC IS APPLIED TO THE CIRCUIT SHOWN AND THE OUTPUT IS THE VOLTAGE ON THE CAPACITOR. IF R=50 OHMS, C=0.03 F AND L=2 H. DETERMINE THE VALUE OF R1 TO HAVE A CRITICALLY DAMPED SYSTEM.a) THE VALUE OF R1 IS
Consider the circuit below with V = 40 V, R1 = 12 ohms, R2 = 18 ohms, R3 = 30 ohms, and C1 = 60 mF. The switch in the circuit has been closed for a long time before it is opened at t = 0. 1:Find the initial voltage across the capacitor. 2:For the natural response of the circuit after t > 0, find the time constant for the circuit. 3:Find the expression for the magnitude of the voltage across the capacitor. 4:Find the expression for the magnitude of the current through R3.
Which of the following is not true? a.Increasing system gain increases stability b.poles farther to the left of imaginary axisimprove speed c.steady-state errors are important in the studyof unstable systems d.multiple poles on the imaginary axis improvessystem stability
An RC circuit is shown to the right. Theresistances of Resistors R0, R1, and R2 are10, 20, and 30 Ohms, respectively. Thevoltage of the battery is 12V, and thecapacitance of the capacitor is 10-4 F. Findthe current in each branch of the circuit att = 0 and t = infinity
Consider the RLC circuit shown where the initial current flowing through the circuit at time t = 0 is I_0 = 5 and the initial charge on the capacitor at time t = 0 is Q_0 = 2. The components have values of R = 100 ohms, L = 5 H, and C = 1/450,500 F. Write the differential equation for Q(t), the charge across the capacitor, assuming the voltage source V(t) = 0