Answer the following and show the Illustraion each problem 2. A 4.6 kg block resting on a smooth horizontal surface is attached to a string that passesover a frictionless pulley as shown in the figure. The pulley has a radius of .48 m. a force of8.5 N pulls the other end of the string. As a result, the block moves a distance of .35m startingform rest. Find the following:a. Acceleration of the blockb. Angular acceleration of the pulleyc. Moment of inertia of pulley 1. A 1500 g object is being pushed by an applied force and accelerates at 4.08 m/se. Whatis the force applied if a frictional force is 62.5 N is acting on opposite direction?2. 2. A 2500 kg truck contains 130 cavans of rice, each with a mass of 50 kg. It is moving ata speed of 5 m/s. How many cavans of rice must be unloaded at a nearby grocery so thatthe truck can move 9 m/s at yet maintain the same momentum?

Given data: Mass of object (m) = 1500 g = 1.500 kg Acceleration (a) = 4.08 m/s2 Frictional force (f)…

Answered: A 1500 g object is being pushed by an…

A 1500 g object is being pushed by an applied force and accelerates at 4.08 m/se. What is the force applied if a frictional force is 62.5 N is acting on opposite direction?

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotation Of A Rigid Object About A Fixed Axis

Section: Chapter Questions

Problem 10.77AP: Review. As shown in Figure P10.77, two blocks are connected by a string of negligible mass passing...

See similar textbooks

Similar questions

A soccer player extends her lower leg in a kicking motion by exerting a force with the muscle above the knee in the front of her leg. She produces an angular acceleration of 30.00 rad/s2 and her lower leg has a moment of inertia of 0.750kg-m2 What is the force exerted by the muscle if its effective perpendicular lever arm is 1.90 cm?
Consider the 12.0 kg motorcycle wheel shown in Figure 10.38. Assume it to be approximately an annular ring with an inner radius of 0.280 m and an outer radius of 0.330 m. The motorcycle is on its center stand, so that the wheel can spin freely. (a) If the drive chain exerts a force of 2200 N at a radius of 5.00 cm, what is the angular acceleration of the wheel? (b) What is the tangential acceleration of a point on the outer edge of the tire? (c) How long, starting from rest, does it take to reach an angular velocity of 80.0 rad/s? Figure 10.38 A motorcycle wheel has a moment of inertia approximately
While punting a football, a kicker rotates his leg about the hip joint. The moment of inertia of the leg is 3.75kgm2 and its rotational kinetic energy is 175 J. (a) What is the angular velocity of the leg? (b) What is the velocity of tip of the punter’s shoe if it is 1.05 m from the hip joint?
Suppose a child gets off a rotating merry-go-round, Does the angular velocity of the merry-go-round increase, decrease, or remain the same if: (a) He jumps off radially? (b) He Jumps backward to land motionless? (c) He jumps straight up and hangs onto an overhead tree branch? (d) He jumps off forward, tangential to the edge? Explain your answers. (Refer to Figure 10.34).
Unreasonable Results A gymnast doing a forward flip lands on the mat and exerts a 500- Nm torque to slow and then reverse her angular velocity. Her initial angular velocity is 10.0 rad/s, and her moment of inertia is 0.050kgm2. (a) What time is required for her to exactly reverse her spin? (b) What is unreasonable about the result? (c) Which premises are unreasonable or inconsistent?
Everyday application: Suppose a yo-yo has a center shaft that has a 0.250 cm radius and that its string is being pulled. (a) If the string is stationary and the yo-yo accelerates away from it at a rate of 1.50 m/s2, what is the angular acceleration of the yo-yo? (b) What is the angular velocity after 0.750 s if it starts from rest? (c) The outside radius of the yo-yo is 3.50 cm. What is the tangential acceleration of a point on its edge?
A cylinder with moment of inertia I1 rotates with angular velocity 0 about a frictionless vertical axle. A second cylinder, with moment of inertia I2, initially not. rotating, drops onto the first cylinder (Fig. P8.73). Because the surfaces are rough, the two cylinders eventually reach the same angular speed . (a) Calculate . (b) Show that kinetic energy is lost in this situation, and calculate the ratio of the final lo the initial kinetic energy. Figure P8.73
A propeller is accelerated from rest to an angular velocity of 1000 rev/min over a period of 6.0 seconds bya constant torque of 2.0103Nm . (a) What is the moment of inertia of the propeller? (b) What power is being provided to the propeller 3.0 s after it starts rotating?
Suppose you start an antique car by exerting a force of 300 N on its crank for 0.250 s. What angular momentum is given to the engine if the handle of the crank is 0.300 m from the pivot and the force is exerted to create maximum torque the entire time?
A large grinding wheel in the shape of a solid cylinder of radius 0.330 m is free to rotate on a friction less, vertical axle. A constant tangential force of 250. N applied to its edge causes the wheel to have an angular acceleration of 0.940 rad/s2. (a) What is the moment of inertia of the wheel? (b) What is the mass of the wheel? (c) If the wheel starts from rest, what is its angular velocity after 5.00 s have elapsed, assuming the force is acting during that time?
Review. As shown in Figure P10.77, two blocks are connected by a string of negligible mass passing over a pulley of radius r= 0.250 m and moment of inertia I. The block on the frictionless incline is moving with a constant acceleration of magnitude a = 2.00 m/s2. From this information, we wish to find the moment of inertia of the pulley. (a) What analysis model is appropriate for the blocks? (b) What analysis model is appropriate for the pulley? (c) From the analysis model in part (a), find the tension T1(d) Similarly, find the tension T2. (e) From the analysis model in part (b), find a symbolic expression for the moment of inertia of the pulley in terms of the tensions T1 and T2. the pulley radius r, and the acceleration a. (f) Find the numerical value of the moment of inertia of the pulley.
A bar on a hinge starts from rest and rotates with an angular acceleration = 10 + 6t, where is in rad/s2 and t is in seconds. Determine the angle in radians through which the bar turns in the first 4.00 s.