A 18.8 kg beam of length L = 39.8 m is attached at an angle of 0 = 36.0° to the side of a building. If the beam is holding up a mass M = 74.4 kg and is supported by a horizontal wire that is attached at location X = 22.3 m (measured along the beam from the building to the wire attachment point), what is the force the building is putting on the beam? Magnitude of force 1402.94 Ф N Direction of force (measured as an angle off of the side of the building (think west of north) 49.4 deg 9

A 18.8 kg beam of length L = 39.8 m is attached at an angle of 0 = 36.0° to the side of a building. If the beam is holding up a mass M = 74.4 kg and is supported by a horizontal wire that is attached at location X = 22.3 m (measured along the beam from the building to the wire attachment point), what is the force the building is putting on the beam? Magnitude of force 1402.94 Ф N Direction of force (measured as an angle off of the side of the building (think west of north) 49.4 deg 9

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure, horizontal scaffold 2, with uniform mass m2 = 29 kg and length L2 = 2.3 m, hangs from horizontal scaffold 1, with uniform mass m1 = 54 kg. A 17 kg box of nails lies on scaffold 2, centered at distance d = 0.80 m from the left end. What is the tension T in the cable indicated?
Forces F1, F2, and F3 act on the structure depicted in the figure, shown in an overhead view. We wish to put the structure in equilibrium by applying a force, at a point such as P located a distance d from F1, whose vector components are Fh and Fv. We are given that a = 2.1 m, b = 2.6 m, C = 1.15 m, F1 = 18.05 N, F2 = 11.05 N, and F3 = 4.85 N.Find Fh.
Forces F→1, F→2, and F→3 act on the structure of the figure, shown in an overhead view. We wish to put the structure in equilibrium by applying a fourth force, at a point such as P. The fourth force has vector components F→h and F→v. We are given that a= 1.90 m, b = 3.27 m, c = 1.31 m, F1 = 38.1 N, F2 = 18.9 N, and F3 = 2.05 N. Find (a) magnitude of Fh, (b) magnitude of Fv, and (c) d.
A uniform plank of length 2.00 m and mass 29.5 kg is supported by three ropes, as indicated by the blue vectors in the figure below. Find the tension in each rope when a 685–N person is d = 0.500 m from the left end. magnitude of T1 = magnitude of T2 = magnitude of T3 =
The rectangular framework is subjected to the following non-concurrent system of forces: a 30lb- force below the origin, a 20lb-force 3ft above the origin and making an angle of 30°NE, a 100lb-force with a horizontal distance of 3ft and a vertical distance of 4ftfrom the origin and making an angle of 45° NW, a 60lb force with the same distance like the previous force but along the positive x-axis, and a 100lbs force 4ft to the right of the origin and making an angle of 60° SW. Determine the magnitude and direction of the resultant, as well as its moment arm relative to the origin.
Two tension ropes are connected to a wall and subject to forces as shown by the diagram below. Determine if the system is in equilibrium. If not, find the direction of the unbalanced force. a. The system is in equilibrium Not in equilibrium, direction = 36.87° clockwise from the horizontal b. Not in equilibrium, direction = 36.87º counter clockwise from the horizontal c. Not in equilibrium, direction = 53.13º clockwise from the horizontal d. Not in equilibrium, direction = 53.13º counterclockwise from the horizontal
Using the same force table that you used, a student was given two forces and asked to find a single force that would produce equilibrium with the two forces. The two forces were given by providing one of the components and the angle the force made with the positive x- axis. The two forces were as follows: Force 1: Fx = −2.70 N; Theta = 220.0 degreees Force 2: Fy = 3.20 N; Theta = 60.0 degrees (a) For each force, calculate the magnitude of the force and the mass required to produce it. (b) Calculate the mass and its angle of application to produce equilibrium with these two forces. Please specify your angle as counterclockwise positive with respect to the positive x-axis.
Using the same force table that you used, a student was given two forces and asked to find a single force that would produce equilibrium with the two forces. The two forces were given by providing one of the components and the angle the force made with the positive x- axis. The two forces were as follows: Force 1: ?? = −2.70 ?; ? = 220.0 degreees Force 2: ?? = 3.20 ?; ? = 60.0 degrees (a) For each force, calculate the magnitude of the force and the mass required to produce it. (b) Calculate the mass and its angle of application to produce equilibrium with these two forces. Please specify your angle as counterclockwise positive with respect to the positive x-axis.
Three concurrent forces have magnitudes of 40, 60, and 50 N, respectively. Determine the smallest angle among them that will produce a state of equilibrium. a. 44.1o b. 4.14o c. 14.4o d. 41.4o
The figure shows an object of mass ?1 = 1.0 kg on an inclined frictionless surface. The angle of theinclined surface is ? = 25 with respect to the horizontal. The object of mass ?1 is connected by anideal string over an ideal pulley to a second object of mass ?2 = 2.05 kg on a horizontal frictionlesssurface below the overhang that is formed by the inclined surface. Furthermore, an external force ofmagnitude ???? = 10 N is exerted on the object with a mass ?1. We observe both objects accelerate. i. Draw separate free-body diagrams of all the forces acting on the two objects ii. Calculate the tension in the string connecting the two objects.
A particle, of mass 6 kg, is in equilibrium on a rough horizontal plane under a force of magnitude T N, which acts at an angle 15 above the horizontal. Given the coefficient of friction between the particle and the rough horizontal plane is 0.35, what values could T take?
Two telephone poles are separated by 40 m and connected by a wire. A bird of mass 0.5 kg lands on the wire midway between the poles, causing the wire to sag 2 m below horizontal. Assuming the wire has negligible mass, what is the tension in the wire?