9) A 2 mm-diameter spherical water droplet with surface tension coefficient of 0.074 N/m². The pressureinside the droplet is -----(a) 37 kPa(b) 80 kPa(c) 74 Pa(d) None of these10) For Newtonian fluids, the relation between the shear stress and the rate of deformation (du/dy) is-------(a) Non linear(b) linear (c) none of the above11) In the figure shown, the-------(a) Adhesion > Cohesion (b) Cohesion > Adhesion

Name: 9) A 2 mm-diameter spherical water droplet with surface tension coeff
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 9) A 2 mm-diameter spherical water droplet with surface tension coefficient of 0.074 N/m². The pressureinside the droplet is -----(a) 37 kPa(b) 80 kPa(c) 74 Pa(d) None of these10) For Newtonian fluids, the relation between the shear stress and the r

Pressure inside droplet is given by P= (4 * surface tension)/(diameter of water droplet) P= ( 4 *…

Engineering

Mechanical Engineering

A 2 mm-diameter spherical water droplet with surface tension coefficient of 0.074 N/m². inside the droplet is ----- 37 kPa (b) 80 kPa (c) 74 Pa (d) None of these ) For Newtonian fluids, the relation between the shear stress and the rate of deformation (du Non linear (b) linear (c) none of the above

A 2 mm-diameter spherical water droplet with surface tension coefficient of 0.074 N/m². inside the droplet is ----- 37 kPa (b) 80 kPa (c) 74 Pa (d) None of these ) For Newtonian fluids, the relation between the shear stress and the rate of deformation (du Non linear (b) linear (c) none of the above

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

By neglecting friction, ( a ) use the Bernoulli equationbetween surfaces 1 and 2 to estimate the volume fl owthrough the orifi ce, whose diameter is 3 cm. ( b ) Why is theresult to part ( a ) absurd? ( c ) Suggest a way to resolve thisparadox and fi nd the true fl ow rate.
Make an analysis of the shape h ( x ) of the water–air interfacenear a plane wall, as in Fig. , assuming that theslope is small, R - 1 ≈ d 2 η / dx 2 . Also assume that the pressuredifference across the interface is balanced by thespecifi c weight and the interface height, ∆p ≈ ρ g η . Theboundary conditions are a wetting contact angle θ at x = 0and a horizontal surface η = 0 as x--->∞. What is themaximum height h at the wall?
FLUID MECHANICS: HYDROSTATICSShow the complete solution.Any method maybe used for those problems which do not specify a methof Answer: 13.734 kPa
Venice, Italy, is slowly sinking, so now, especially inwinter, plazas and walkways are fl ooded during storms.The proposed solution is the fl oating levee of Fig. .When fi lled with air, it rises to block off the sea. The leveeis 30 m high, 5 m wide, and 20 m deep. Assume a uniformdensity of 300 kg/m 3 when fl oating. For the 1-m sea–lagoon difference shown, estimate the angle at which thelevee fl oats.
A settling tank for municipal water supply is 2.5 m deep,and 20°C water fl ows through continuously at 35 cm/s.Estimate the minimum length of the tank that will ensurethat all sediment (SG = 2.55) will fall to the bottom forparticle diameters greater than (a) 1 mm and (b) 100 μm.
1 Consider a rapidly rotating (ie, in near geostrophic balance) Boussineq fluid on the f plane. A) Show that the pressure divided by the density scales as Φ ≈ fUL B) Show that the horizontal divergence of the geostrophic wind vanishes. Thus, argue that the scaling W ≈ UH = L is an overestimate for the magnitude of the vertical velocity
When water at 20 °C is in steady turbulent fl ow through an8-cm-diameter pipe, the wall shear stress is 72 Pa. What isthe axial pressure gradient (∂p/∂x) if the pipe is (a) horizontaland (b) vertical with the fl ow up?
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
We are given laboratory data, taken by Prof. Robert Kirchhoffand his students at the University of Massachusetts, for thespin rate of a 2-cup anemometer. The anemometer wasmade of ping-pong balls ( d = 1.5 in) split in half, facing inopposite directions, and glued to thin ( 1/4-in) rods pegged toa center axle. There were fourrods, of lengths l = 0.212, 0.322, 0.458, and 0.574 ft. Theexperimental data, for wind tunnel velocity U and rotationrate Ω , are as follows: Assume that the angular velocity Ω of the device is afunction of wind speed U , air density ρ and viscosity μ , rodlength l , and cup diameter d . For all data, assume air is at1 atm and 20 ° C. Defi ne appropriate pi groups for thisthe problem, and plot the data in this dimensionless manner.Comment on the possible uncertainty of the results.As a design application, suppose we are to use thisanemometer geometry for a large-scale ( d = 30 cm) airportwind anemometer. If wind speeds vary up to 25 m/s and wedesire an average…
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
A pipeline 0.5 m diameter and 1200 m long is used for transporting an oil of density 150 kg/m3 and of viscosity 0.91 Pa-s at 0.4 m2/s. If the roughness of the pipe is 0.5 mm, what is the pressure drop?
The head loss for a certain circular pipe is given by hL = 0.0826fL(V.2/D5), where f is the friction factor (dimensionless), L is the pipe length, V. is the volumetric flow rate, and D is the pipe diameter. Determine if the 0.0826 is a dimensional or dimensionless constant. Is this equation dimen sionally homogeneous as it stands?