A 200-mm lever and a 240-mm-diameter pulley are welded to the axle BE that is supported by bearings at C and D. If a 720-N vertical load is applied at A when the lever is horizontal, determine (a) the tension in the cord, (b) the reactions at C and D. Assume that the bearing at D does not exert any axial thrust. 40 mm SO mm 120 min 200 mm 130 720 N

A 200-mm lever and a 240-mm-diameter pulley are welded to the axle BE that is supported by bearings at C and D. If a 720-N vertical load is applied at A when the lever is horizontal, determine (a) the tension in the cord, (b) the reactions at C and D. Assume that the bearing at D does not exert any axial thrust. 40 mm SO mm 120 min 200 mm 130 720 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

The pin at O can support a maximum force of 3.5 kN. What is the corresponding maximum load L which can be applied to the angled bracket AOB? A. 0.541 kN C. 2.632 kN B. 1.676 kN D. 3.091 kN
The pipe ACDE is supported by ball-and-socket joints at A and E and by the wire DF . Determine the tension in the wire when a 640-N load is applied at B as shown.
Before the load is placed on the rigid plate, the top of the central spring is 20 mm lower than the outer springs. Each outer spring is made of 24 turns of 15-mm diameter wire on a mean radius of 60 mm. The central spring consists of 16 turns of 20 mm dimeter wire on a mean radius of 80 mm. If a load P = 5 kN is now placed on the rigid plate. Disregarding the weight of the plate, use G = 83 GPa and use Light spring formula. Determine the maximum shearing stress of the in uter spring. In MPa
Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at A. Draw the FBD for the bar, recognizing that it is a two-force body. Determine the number of unknowns.
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
PROBLEM 1: Determine the tension in each cable and the components offorce reaction at D needed to support the load. Required: 1. Find Dx (Answer: 1039.230 N), Dy (Answer: 0 N) and Dz (Answer: 0 N) 2. Find Tension AB (Answer: 467.667 N) and Tension (Answer: AC 673.808)
A vertical load P is applied at end B of rod BC. (a) Neglecting the weight of the rod, express the angle 0 corresponding to the equilibrium position in terms of P, l , and the counterweight W. (b) Determine the value of 0 corresponding to equilibrium if P= 2W.
Static Problem. Indications:The system shown is composed of an ABG bar, supported by a pin at point A and by a collarsmooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and theRod BDE is supported by a pin at D and a cable at end E.Based on the above, determine:a) The load P, such that the cable force EF is T.b) The internal loads in a section passing through point G (normal and shear force, and momentflexing).c) Draw bar BDE horizontally and generate the shear force and moment diagramsflexing Indicate the maximum values of shear force and bending moment and their location.?= 22 lb ? = 7 in ? = 6 in
A 1-in.-square aluminum strut is maintained in the position shown by a pin support at A and by sets of rollers at B and C that prevent rotation of the strut in the plane of the figure. Knowing that LAB= 3 ft, LBC=4 ft, and LCD=1 ft, determine the allowable load P using a factor of safety with respect to buckling of 3.2. Consider only buckling in the plane of the figure and use E=10.4 *106 psi.
A35-kg disk rests on an inclined surface for which µs = 0.2. The disk is connected to a beamby pin connection at A and the link is supported by pin at B. The vertical load P is applied onthe link AB at a location as shown in Figure 3 (b) Determine the support reactions at pin A and B
A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kN including its self-weight which is distributed equally:a. Determine the stress on the lower washers before the buts are tightened. b. Determine the stress in the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt.c. Determine the stress in the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt.
Solve Prob. 4.123, assuming that the 1.8-kN load is applied at C.(Reference to Problem 4.123):The rigid L-shaped member ABC is supported by a ball-and-socket joint at A and by three cables. If a 1.8-kN load is applied at F , determine the tension in each cable.