A 220V short-shunt compound generator has armature resistance, series field resistance and shunt field resistances of 0.6, 0.44 and 300 - 16 respectively. If the generator supplies a 10+16 kW load at a rated voltage, find the induced voltage in the armature. Ignore armature reaction. Find the efficiency if the mech and core loss is 500W

A 220V short-shunt compound generator has armature resistance, series field resistance and shunt field resistances of 0.6, 0.44 and 300 - 16 respectively. If the generator supplies a 10+16 kW load at a rated voltage, find the induced voltage in the armature. Ignore armature reaction. Find the efficiency if the mech and core loss is 500W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

A shunt generator supplies a 20kW load at 200V through cables of resistance, R= 100mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =40mΩ, determine (a) the terminal voltage, and (b) the e.m.f. generated in the armature
A short shunt compound generator has an armature; series field and shunt field resistances of 0.031Ω, 0.04Ω and 100Ω respectively. At rated load condition, the terminal voltage is 400V while the armature is developing an emf of 409V. Find the kW delivered to the load at rated condition.
A shunt generator supplies a 33kW load at 225V through cables of resistance, R = 100mΩ. If the field winding resistance, Rf =56Ω and the armature resistance, Ra =40mΩ. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
A 3 phase 4MVA, 12 kV star connected synchronous generator has Zs= 0.8+J30 ohm. Using circle diagram only, find: 1. The output power developed at unity power factor with excitation equal to 1.25 of rated voltage. 2. The load angle and power factor if the generator supplies (1500 KW) at rated voltage and excitation lequal to (1.2) of rated voltage. 3. Repeat part (2) when .armature resistance is neglected
A long-shunt compound d.c. generator with armature, series field and shunt field resistance of 0.5, 0.4 and 250 Ω respectively gave the following readings when run at constant speed : Load current (A) : 0 10 20 30 40Terminal p.d. (V) : 480 478 475 471 467 Plot the curve of internal generated e.m.f. against load current. Explain fully the steps by which this curve is obtained and tabulate the values from which it is plotted.
Determine the e.m.f. generated of a short-shunt compound generator supplies 100 A at 400 V. If the field resistance, Rf =20 Ω, and the armature resistance, Ra =0.06 Ω. If you know that the volt drop in series winding is 2 V
Problem: The field current of a 100-kW, 250V shunt generator is 5A when delivering power at rated terminal voltage and rated load current. The combined armature and brush resistance is 0.1 ohm. 1.)Calculate the generated power in kW. 2.)What is the electrical efficiency? * Formatt: given required solution answer
A 3 phase, star connected synchronous generator supplies current of 10A having phase angle of 20º lagging at 400V. Find the load angle and the components of armature current Id and Iq if Xd = 10 ohm and Xq = 6.5 ohm Assume armature resistances to be negligible
A long-shunt, four pole, 1500-W, 250-V, duplex wave-wound DC compound generator with the rated speed of 500 r.p.m., has a shunt field resistance of 100 Ω, a series field resistance of 0.05 Ω and an armature resistance of 0.2 Ω. If the flux per pole is 48.798 mWb and a total of 620 conductors, calculate the following: (a) the generated voltage, (b) the field currents, (c) the power generated in the armature.
The output of a shunt generator is 66 A at 100 volts. Armature and field resistances are, respectively, 0.04 ohm and 25 ohms. If the efficiency at this load is 88%, determine the core and friction losses
A long shunt compound generator delivers 100 A at 250 V. The armature, shunt field and series field resistances are 0.02 Ohms, 50 Ohms and 0.05 Ohms respectively. If the Break Horse Power (BHP) or the power developed by the shaft torque of the driving engine is 40, determine the stray loss.
A short shunt compound DC generator delivers a load current of 30 A at 220 V and has armature, series field and shunt field resistances of 0.05, 0.3 and 200Ω respectively. Calculate the induced emf, the armature current and the voltage regulation. Allow 1 V per brush for contact dro