2.11. The normalized radiation intensity of a given antenna is given by (f)sin²0sin³Ø The intensity exists only in the 0s0sn, Ospsn region, and it is zero elsewhere. Find the (a) Exact directivity (dimensionless and in dB). (b) Azimuthal and elevation plane half-power beam widths (in degrees). Sol/ 4n U max D= P rad

2.11. The normalized radiation intensity of a given antenna is given by (f)sin²0sin³Ø The intensity exists only in the 0s0sn, Ospsn region, and it is zero elsewhere. Find the (a) Exact directivity (dimensionless and in dB). (b) Azimuthal and elevation plane half-power beam widths (in degrees). Sol/ 4n U max D= P rad

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The normalized radiation intensity of a given antenna is given by(a) U = sin θ sin φ (b) U = sin θ sin2 φ(c) U = sin θ sin3 φ (d) U = sin2 θ sin φ(e) U = sin2 θ sin2 φ (f) U = sin2 θ sin3 φThe intensity exists only in the 0 ≤ θ ≤ π, 0 ≤ φ ≤ π region, and it is zeroelsewhere. Find the(a) exact directivity (dimensionless and in dB).(b) azimuthal and elevation plane half-power beamwidths (in degree
A 5.0 × 2.0 mm2air-filled rectangular waveguide is to operate below85 GHz. Determine the number of TE and TM modes that can be transmitted in the waveguide. Subsequently, sketch the cross-sectional view of field line distributions for TE10, TE11, and TM11 modes.
A 0.48520λ0 dipole antenna is made to work at 4 GHz. The antenna is then connected to a 12 V voltage source which has an internal resistance of 25 Ω) a) Make a diagram of the above system, b) Is an impedance matching circuit needed? If yes, where should the impedance circuit be inserted and make a diagram of the system with the adjusting circuit, c) How many cm is the length of the dipole antenna above, d) How much power is emitted when not using the adjusting circuit and e) How much power is emitted when using the adjusting circuit. Solve subparts D,E max 20 minutes ASAP
A microwave link includes two sites that are 10 km apart and uses a center frequency of 9 GHz. On either transmitter or receiver side, a 100-m transmission line that has an attenuation per unit length of 0.01 dB/m is connected to an amplifier and a parabolic reflector antenna. Other losses caused by connectors and insertions incurred on one side amounts to 3 dB. Antenna has a power gain of 20 dB. If the output of the transmitter amplifier is 30 dBm, what is the received signal level (in dBm) at the input of the receiver amplifier?
Calculate the geometric factor for a resistivity test with an aperture of L=500 meters using the dipole-dipole arrangement with a factor n=8 with a value of a=50 m
In an air-filled rectangular waveguide, the cutofffrequency of a TE10 mode is 5 GHz, whereas that ofTE01 mode is 12 GHz. Calculate(a) The dimensions of the guide.(b) The cutoff frequencies of the next threehigher TE modes.(c) The cutoff frequency for TE11 mode if theguide is filled with a lossless material havingr = 2.25 and r = 1.
Consider a communication link operating at 15 GHz with the transmitting and receiving antennas gain of 20 dB and 15 dB, respectively. The transmitted power is 15 W and the distance between transmitter and receiver is 12 km. (i) Determine the received signal (in dBm) for the free space condition. (ii) Repeat (i) if plane earth path loss exists and both transmitting and receiving antenna height is 10m. (iii) If there is a 20-meter tall building located at 5 km from the transmitter, determine the minimum height of transmitting and receiving antennas above ground level to ensure unobstructed LOS conditions.
if in a rectangular waveguide for which a=2b , the cuttoff frequency for TE02 mode is 12 GHz ,the cutoff frequency for TM11 mode is
A 0.48520λ0 dipole antenna is made to work at 4 GHz. The antenna is then connected to a 12 V voltage source which has an internal resistance of 25 Ω) a) Make a diagram of the above system, b) Is an impedance matching circuit needed? If yes, where should the impedance circuit be inserted and make a diagram of the system with the adjusting circuit, c) How many cm is the length of the dipole antenna above, Solve Subparts A,B,C in 25 minutes ASAP
If the material between the ground plates of a 100 ohm strip line to be used at 12 GHz has a relative dielectric constant of 2.19 and a loss tangent of 0.01, what is the dielectric loss of the strip line in Np/m?
A circular loop, of loop radius λ/30 and wire radius λ/1000, is used as a transmitting/receiving antenna in a back-pack radio communication system at 10 MHz. The wire of the loop is made of copper with a conductivity of 5 .7 ×10 7 S/m. Assuming the antenna is radiating in free space, determine the(a) radiationresistan ce of the loop; (b) loss resistance of the loop (assume that its value is the same as if the wire were straight ); (c) input resistance; (d) input impedance; (e) radiation efficiency.
1.) A communication system is defined below:Transmitter Power: = 45 dBm; Frequency = 1 GHzTransmit Antenna: Gain = 12 dB, height above ground = 50 meters;Receive Antenna: Gain = 6 dB, height above ground= 2.5 metersFind the received power (in dBm) at a range of 4 kilometers:a. using the free-space range equation b. using the near-earth range equation Using the results of the calculations in a & b above: c. determine the best prediction of the received power (in dBm) at the 4 kilometer range. 2.) A transmitter operating at 80 MHz has an output power of 1.5 kW which is fed to an antenna with a gain of 20 dB. Determine the "keep-out" distance (in meters) required to meet the safety standard. clear and easy to understand. Thanks