A 230 Vms, 50 Hz AC supplies a circuit consists of resistor 7 2 and inductor 31.8 mH connected in series, calculate: i) The impedance, Z ii) The rms current, Ims and the phase angle iii) The power factor iv) The average power in kW, P v) The reactive power in KVAR, Q vi) The apparent power in kVA, S

A 230 Vms, 50 Hz AC supplies a circuit consists of resistor 7 2 and inductor 31.8 mH connected in series, calculate: i) The impedance, Z ii) The rms current, Ims and the phase angle iii) The power factor iv) The average power in kW, P v) The reactive power in KVAR, Q vi) The apparent power in kVA, S

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The values of the parameters in the circuit shown are L1=8 mH; L2=2 mH; k=0.75; Rg=1 Ω; and RL=7 Ω. Ifvg=542 cos 1000t V, find 1. a) the rms magnitude of vo;2. b) the average power delivered to RL;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to RL.
For the frequency-domain circuit , calculate: 1. a) the rms magnitude of Vo;2. b) the average power dissipated in the 9 Ω resistor;3. c) the percentage of the average power generated by the idealvoltage source that is delivered to the 9 Ω load resistor.
five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let R= 200, L=0.400H,C=6.0 Mf, and V=30.0 v. what's the reading of the voltmeter's V1,V2,V3,V4 and V5 if W= 200 rad/s
An investor own two large stores at Dubai. Both malls are connected in parallel and operating at an unknown voltage. The local utility system voltage is 13.8 kVrms and supplied power to the malls through a feeder line with impedance equal to 1+j2.5 ohms. Store 1 is consuming 400 kW at 0.8 pf lagging while Store 2 is consuming 300 kVAR at 0.75 pf lagging. Determine the following: a) The stores' operating rms voltages. b) The total real and reactive power of the ehole system. c) The overall pf of the whole system.
An AC generator having an internal resistance of 2 k*(omega) is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, E = 282 sen (100*pi*t) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
A residential electric power monitoring system ratedfor 120-V rms, 60-Hz source registers powerconsumption of 1.2 kW, with a power factor of 0.8.Finda. The rms current.b. The phase angle.c. The system impedance.d. The system resistance.
An example power system has two distinct manufacturing areas, one with harmonic loads, and another with only linear loads. The portion of the system with the harmonic loads draws 75 A rms at 60 Hz, 10 A rms at 300 Hz, and 5 A rms at 420 Hz. The part of the system with only linear loads draws 75 A rms at 60 Hz. (i) What is the total load current (at 60 Hz) if both manufacturing plants are running? Calculate the THD. (ii) What is the total load current (at 60 Hz) if only the manufacturing plant with harmonic loads is running? Calculate the THD.
When connected to a 120 V (rms), 60-Hz power line, a load absorbs 4kW at a lagging power factor of 0.8. Find the value of Capacitance, C, necessary to raise the power factor to 0.95 lagging.
Obtain the power factor ( PF ) , apparent power ( S ) ,Real Power (P) &the Reactive Power (Q ) of a load whose impedance is Z= 60+j40Ω when the applied voltage Is 320 cos(377t +10o) V
A load with a voltage amplitude of 50 Hz 300 V rms at its terminals consumes 28.98 kW at a back power factor of 0.69. If a 225.87 microfarad capacitor is connected parallel to the terminals of this load, how much will the amplitude of the current drawn from the line decrease?
A motor connected to a 220-V supply line from the power company has a current of 7.6 A. Both the current and the voltage are rms values. The average power delivered to the motor is 1317 W. (a) Find the apparent power, the reactive power, and the power factor when ω=377 rad/s. (b) Find the capacitance of a parallel capacitor that will result in a unity power factor of the combination. (c) Find the current in the utility lines after the capacitor is installed.
The two loads shown can be described as follows: Load 1 absorbs an average power of 60 kW and delivers 70 kVAR of reactive power; Load 2 has an impedance of (24+j7) Ω. The voltage at the terminals of the loads is 25002 cos 120π t V.1. a) Find the rms value of the source voltage.2. b) By how many microseconds is the load voltage out of phase withthe source voltage?3. c) Does the load voltage lead or lag the source voltage?