Fill in the blanks:A 240 V shunt motor has an armature resistance of 0.5 0 and field resistance Of 120 Q. Determine the back emf when giving anoutput of 10 kWat 83% efficiencyFill in the space provided for your answer.Ep

Given: A shunt motor with, V=240 VRa=0.5 ΩRf=120 ΩP0=10 kWη=83%=0.83

A 240 V shunt motor has an armature resistance of 0.5 Q and field resistance 0f 120 Q. Determine the back emf when giving an output of 10 kWat 83% efficiency Fill in the space provided for your answer. Ep =

A 240 V shunt motor has an armature resistance of 0.5 Q and field resistance 0f 120 Q. Determine the back emf when giving an output of 10 kWat 83% efficiency Fill in the space provided for your answer. Ep =

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Related questions

Q: . A commercial analog linear sensor has two sample measurements (x₁, Vout,1)=(1, 3V) and (x2,…

Q: 18.7 Select the values of R₁, R2, and R3 in the circuit in Fig. P18.7 so that h₁14, 12 0.8, h21…

Q: A 440V, 3-phase , 4-pole , 50hz, 37.3 kW, wye connected induction motor has the following parameter.…

Q: 4-1. An air-filled rectangular waveguide has dimensions of a = 6 cm and b = 4 cm. The signal…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Describe what the terms Gain Bandwidth Product (GBP) and Slew Rate mean in the context of an…

A: In this question we will define gain bandwidth product and slew rate of opamp....

Q: An electron is bound in a one-dimensional infinite potential well with a width of 10 Å. If the…

Q: E = 30 V < 30° R 3 Ω XL 8 Ω Xc •6Ω E, = 60 V < 10°

A: As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Q: mathematical expression for iC(t)

A: For KVL equations- Summation of voltage drops in a closed loop is always zero. For KCL equations-…

Q: υπ +1 10Ω t=t2 + 191 31Η t=11 1002 201 2 Ug = (5 + 2)v v, = (5 – 2)v 1+ την

Q: In a series connection with 2 resistors, If the current total is 3 amperes and the total voltage is…

Q: 8. (a) A parabolic antenna with a diameter of 0.75 meter is used to receive a 6GHz satellite signal.…

Q: Problem 2: iB! t=0 10 mA 50 kn 5 km 20 nF ΚΩ • In the circuit shown above the dependent current…

A: The given circuit is shown below. The value of the dependent source current is iβ. We need to find…

Q: Why use Inductors in a circuit?

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 5. It is expresses the ratio of energy wasted to the energy stored in a capacitor. 6. It is the…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 3. Obtain the state model for the block diagram shown. 1/s+1 U(s) 1/s 1/s+2 Y(s)

A: In this question we need to find a state model of the given block diagram

Q: From the given network, find the current I in XL using Nodal, Mesh, Superposition, Thevenin's, and…

A: NOTE:- As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly…

Q: 2. A single transistor amplifier is shown in the circuit to the right. The input is a 100 kHz sine…

A: In the given question, we have to do the DC analysis and then need to find the DC current through…

Q: 17. control can reduce system overshoot of a closed-loop control system. (a) D-mode (b) P-mode (c)…

Q: How long do i need to charge a 12V battery in 6V solar panel?

A: If a 6 V solar pannel is used to charge a 12 V battery then there will not be enough energy provided…

Q: 3b) Calculate v, in the circuit shown. 1H 22 12 cos 4 V 4 H 2H ww ell

Q: Find C/R using Mason's gain formula. G₁ G2 H3K Hi H₂K

Q: 10) In a synchronous (coherent) detector, Ifthere is a phase shift 90o between the local oscillator…

A: We need to find out output of detector

Q: Which one of the following statements is FALSE for a bipolar transistor? The emitter region has a…

A: Some facts about bipolar junction transistor

Q: An induction motor, 3phase, 60 hertz, 6-pole, 264 V, has a stator connected in Y and rotor in Y. If…

A: The solution is given below

Q: 2. A proportional control function u(t) = 3 + 10e(t) is used in a closed-loop control system. If the…

Q: 22. A commercial strain gauge has Gauge Factor GF=2 and initial resistance Ro = 120Ω. If the strain…

Q: What is un-bypassed Rs and bypassed Rs?

A: In the BJT emitter resistance can be bypassed or un-bypassed. as shown in figure1 Rs is bypassed and…

Q: Note: Show your solutions, no solutions means wrong answers VCC Vin = 5v Ov Find Icsat,Ibsat, Vrc,…

A: According to the question, for the given circuit shown below We need to find IC,sat ; IB, sat ; VRc…

Q: with a closed-loop Design a non-inverting amplifier gain of Av: 5. The output voltage is limited to…

A: It is given that: Av=5 VVo=-10 V≤Vo≤10 VImax=50 μA

Q: 3. A type J thermocouple is used to measure temperature with reference temperature 20 °C. If the…

A: Thermocouple: A thermocouple is made consisting of a welded 'hot' junction between two dissimilar…

Q: Find the waveform, f(t), from its Laplace transform, F(s), by doing a partial fi expansion. 4(s + 3)…

A: In this question we will find f(t) by inverse Laplace transform using partial fraction expansion....

Q: Find i, (t) and ialt)

A: The current in both primary and secondary side of the mutually coupled circuit can be obtained by…

Q: 2. Find IB, IC, IE, VCE and VCB for the common emitter configuration of a PN transistor. Rc 390 2 RB…

A: In this question, We need to determine the current IB , IC , IE and voltage VCE , VBE and VCB…

Q: 20. A dummy strain gauge is used in a quarter Wheatstone bridge circuit to (a) measure applied…

A: A strain gauge is an electrical sensing device it's resistance varies with the applied force,

Q: The steady-state concentration of excess carriers at x = 0 is Sp(0) = n(0) = 2 × 10¹4 cm3 -3 .…

A: Given: Consider a bar of p-type silicon that is uniformly doped to a value of Na = 2 × 1016 cm−3 at…

Q: Design synchronous counter for sequence 4-2-4-2 using JK Flip-Flop

A: The synchronous counter for the given sequence can be designed by using three JK flipflop.

Q: Q1): Find the T.F of DE (h[n]) Y[n] 2X[n] -Y[n-1] +X[n-1] -Y[n-1]+6Y[n-2]+4Y[n-2]-2Y[n-2] +X[n-1]…

Q: Find the Thévenin and Nortons equivalent circuit for the portions of the networks in the figure…

Q: 15. The output function Vout= A(V₂ - V₁) of a differential op-amp circuit is used in si…

A: The differential amplifier are nothing but the specific arrangement of operational amplifier in…

Q: Question 2 Neglecting the effects of friction, derive a transfer function for the system below, from…

Q: 11. A parallel plate capacitor has the following values k=81, d=0.025 inches, A= 6 square inches.…

Q: Choose the correct mode of operation for each MOS band diagram below. Vacuum level Vacuum level En…

A: We need to choose the correct mode of operation for each Mos band diagram.

Q: 13.46 A communication link uses a half-wave dipole antenna for transmission and another half-wave…

A: It is given that: R=80 km=80000 mPr=0.5 μW=0.5×10-6 Wf=20 MHz=20×106 Hz

Q: 3. A type J thermocouple is used to measure temperature with reference temperature 20 °C. If the…

A: Thermocouple: A thermocouple is made consisting of a welded 'hot' junction between two dissimilar…

Q: Voltage across capacitor is ve. With ve and it as a set of state variables derive the state model.

Q: Neglecting the effects of friction, derive a transfer function for the system below, from XI(s) to…

Q: ① 24V 2MF ㅏ C₁ C₂ S 2MF 2mF ㅔ HMF C4 Cs 2mF Co -1106 AMF

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: t=0 FR E ZL= ∞0 1=1m I need to convert the drawing from a handwritten drawing to a typeface on the…

A: Given circuit,

Q: 3. If D = 2r a, C/m², find the total electric flux leaving the surface of the cube, 0 < x, y, z <…

Q: 3. If the switch changes position (from b-c to a-b) at t-0, find the capacitor voltage ve(t) for…

A: Capacitor- capacitors are widely used in electronic circuits to block direct current power while…

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

Fill in the blanks:
A 240 V shunt motor has an armature resistance of 0.5 0 and field resistance Of 120 Q. Determine the back emf when giving an
output of 10 kWat 83% efficiency
Fill in the space provided for your answer.
Ep

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Name three factors that determine the torque produced by an induction motor.
A motor is operating a load that requires a torque of 750 lb-in. and is turning at a speed of 1575 RPM. How much hp is the motor producing?
A 440 V, shunt motor has armature resistance of 0.8 ohm and field resistance of 200 ohm. Determine theback emf when giving an output of 7.46 kW at 85% efficiency.
3. A shunt motor running at 600 rpm takes 80 A at 250 V. Armature resistance is 0.1 ohm. Shunt field resistance is 50 ohms. If the iron and friction losses amount to 2188 W determine the shaft torque. A. 250 N-m B. 224 N-m C. 254 N-m D. 204 N-m
A compound motor develops a torque of 271 lb-ft when it is operating at 1200 rpm, under which condition its armature current Ia is 215 amperes. What will be the developed horsepower of the motor if the load is increased so that it slows down to 1,1120 rpm in which case Ia changes to 238 amperes and the total flux increases by 8 percent?
A short shunt compound generator supplies a current of 100A at 220V. If the resistance of the shunt field is 50Ω, of the armature 0.05Ω, the total brush drop is 2V and the iron and friction losses amount to 1 kW, find the bhp of the engine driving this generator.
A 145 -V shunt motor has an armature and shunt field resistances of 0.38 and 182 Ohms respectively. This motor draws 26 A of current from its source. Its rotational losses amount to 822 W. If the brush contact drop is 2.06 V total, find the motor's horsepower output.
On no-load, a shunt motor takes 5 A at 250 V, the resistances of the field and armature circuits are 250 Ω and 0.1 Ω respectively. Calculate the output power and efficiency of the motor when the total supply current is 81 A at the same supply voltage. State any assumptions made.
A 200V shunt motor develops 23hp, when taking 20.2 kW. The field resistance is 50 ohms and the armature resistance is 0.06 ohm. What is are the rotational losses? a. 1125 W b. 1667 W c. 917 W d. 825 W
a 20kw, 200v dc shunt motor has an electrical efficiency of 86% and an armature resistance of 0.25ohms what is the value of shunt field resistance in ohms
A series motor with unsaturated magnetic circuit and negligible resistance, when running at a certain speed on a given load, takes 50 Amp at 500 Volts. If the load torque varies as the cube of the speed. Find the resistance necessary to reduce the speed by 20%
A universal motor has armature circuit resistance of 15 ohm and inductanceof 0.3H. On being connected to a 220 V dc supply, it draws 1.5 A from themains and runs at 2000 rpm. Find the speed and power factor of the motor,when connected to a 230 V, 25 Hz supply and drawing the same armaturecurrent.