I need help with all the parts. G GmailVroA 25-kg uniform beam with a length of 12-m is connected to a wall through a hinged connection and a cable asshown below. The beam supports a load of 75-kg. Draw a free-body diagram for the beam and determine;Cd@a.b.0.d.e.mycourses.rcsj.edu/webapps/assessment/take/launch.jsp?course_assessment_id=_98608_18course idYouTube MapsNew Tab S G GoogleThe torque produced by the load with respect to point C in Newton-meters.The tension in the cable in Newtons.The x component of the reaction force (Rx) at point C in Newtons.They component of the reaction force (Ry) at point C in Newtons.The direction of RyO 21 11309 m6-mC1.12,8782. 138.63. 10,9324. 19815. 93266.7.8.UpwardDownward287.49.223.710. 735011. 384212. 882013. 228714. 163.515. 1563

Given: Mass of load, m=75 kg Mass of rod, 25 kg Distance of load from point c=12 m Distance of COM…

A 25-kg uniform beam with a length of 12-m is connected to a wall through a hinged connection and a cable as shown below. The beam supports a load of 75-kg. Draw a free-body diagram for the beam and determine; a. The torque produced by the load with respect to point C in Newton-meters. b. The tension in the cable in Newtons. d. e. The x component of the reaction force (Rx) at point C in Newtons. They component of the reaction force (Ry) at point C in Newtons. The direction of Ry 12-m 30 WI 6-m 9-m

A 25-kg uniform beam with a length of 12-m is connected to a wall through a hinged connection and a cable as shown below. The beam supports a load of 75-kg. Draw a free-body diagram for the beam and determine; a. The torque produced by the load with respect to point C in Newton-meters. b. The tension in the cable in Newtons. d. e. The x component of the reaction force (Rx) at point C in Newtons. They component of the reaction force (Ry) at point C in Newtons. The direction of Ry 12-m 30 WI 6-m 9-m

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter8: Rotational Motion

Section: Chapter Questions

Problem 74A

See similar textbooks

Similar questions

In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
In order to lift a shovelful of dirt, a gardener pushes downward on the end of the shovel and pulls upward at distance l2 from the end, as shown below. The weight of the shovel is mg and acts at the point os application of F2 . Calculate the magnitudes of the forces F1 and F2 as functions of l1 , l2 , mg, and the weight W of the load. Why do your answers not depend on the angle that shovel makes with the horizontal?
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
A uniform, 8.00 m, 1150kg beam is hinged to a wall and supported by a thin cable attached to a 2.00 m from the free end of the beam as shown. Find the tension in the thin cable. Do not forget the force of gravity on the beam. b) How hard does the beam push inward on the wall? what is the horizontal force on the beam from the wall?
A large advertisement board (W) is held in position by cable F1 , with a breaking strength of 1500 N and a wooden strut F2 with a breaking strength of 750 N. Calculate the maximum weight on the board can hold.
A uniform steel bar of length 10 m is supported at point A and B using two cables as shown in the figure. The bar is hinged at point C and has a weight 500 N. What is the tension (T) force in the cable?
A boom with an angle of theta, supports a 1000 lbs load as shown in the figure. Assume that the force exerted by the boom is 3 times the force exerted by the cable that holds it in place, what is the force exerted by Cable A?
A large advertisement board (W) is held in position by cable F1, with a breaking strength of 1500 N and a wooden strut F2 with a breaking of 750 N. Calculate the maximum weight the board can hold.
Suppose the weight of the drawbridge in Figure shown is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
A post with a horizontal and inclined member supports a box whose weight is P, as shown in the figure. Determine the force exerted by the member BC
In the strict curl weightlifting event, a standing athlete lifts a barbell using only their lower arms, hinging at the elbow. The record weight is 900N. The biceps tendon connects 4.00cm from the elbow and pulls straight up, while the barbell is held 35.0cm from the elbow. Assume the weight of the forearm is negligible, and that each arm supports half the weight of the barbell. A) What is the tension in the tendon connecting the bicep to the forearm while held stationary in the position shown? B) What is the force (magnitude and direction) of the upp arm pushing on the forearm at the elbow joint?
The beam AB of length L shown in Figure 3 is subjected to a distributed load w=w(x) given by: ?(?) = ????? (?? /2?) where wo is a constant and the x-coordinate measures horizontal distance from the left end A of the beam. The beam is supported at its left end A by a pin and at its right end B by a roller, as shown. a) Find a single force F and the distance d (measured to the right of point A) at which it must act so that F alone is statically equivalent to the distributed load w=w(x) acting on the beam. Express your results in terms of wo and L. b) Find the reactions exerted by the wall at A.