A 292 turn circular coil of diameter 54 cm is placed in the earth's magnetic field 0.42 G, such that its magnetic dipole moment makes an angle 31° wi the field as shown in the picture. If the current in the circular coil is 120 A, then calculate the following: a) The magnetic dipole moment of the coil in Am2 = b) The torque on the current loop measured in Nm = c) The potential energy of the current loop in joules = ol

A 292 turn circular coil of diameter 54 cm is placed in the earth's magnetic field 0.42 G, such that its magnetic dipole moment makes an angle 31° wi the field as shown in the picture. If the current in the circular coil is 120 A, then calculate the following: a) The magnetic dipole moment of the coil in Am2 = b) The torque on the current loop measured in Nm = c) The potential energy of the current loop in joules = ol

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter11: Magnetic Forces And Fields

Section: Chapter Questions

Problem 89AP: The current through a circular wire loop of radius 10 cm is 5.0 A. (a) Calculate themagnetic dipole...

See similar textbooks

Similar questions

A wire of length 1.0 m is wound into a single-turn planar loop. The loop carries a current of 5.0 A, and it is placed in a uniform magnetic field of strength 0.25 T. (a) What is the maximum torque that the loop will experience if it is square? (b) If it is circular? (c) At what angle relative to B would die normal to the circular coil have to be oriented so that the torque on it would be the same as the maximum torque on the square coil?
A 5.0-m section of a long, straight wire carries a current of 10 A while in a uniform magnetic field of magnitude 8.0103T . Calculate the magnitude of the force on the section if the angle between the field and the direction of the current is (a) 45°; (b) 90°; (C) 0°; or (d) 180°.
A solenoid with an iron core is 25 cm long and is wrapped with 100 turns of wire. When the current through the solenoid is 10 A, the magnetic field inside it is 2.0 T. For this current, what is the permeability of the iron? If the current is turned off and then restored to 10 A, will the magnetic field necessarily return to 2.0 T?
Sodium ions (Na+) move at 0.851 m/s through a blood-stream in the arm of a person standing near a large magnet. The magnetic field has a strength of 0.254 T and makes an angle of 51.0 with the motion of the sodium ions. The arm contains 100 cm3 of blood with a concentration of 3.00 1020 Na+ ions per cubic centimeter. If no other ions were present in the arm, what would be the magnetic force on the arm?
How is the percentage change in the strength of the magnetic field across the face of the toroid related to the percentage change in the radial distance from the axis of the toroid?
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
Two flat, circular coils, each with a radius R and wound with JV turns, ace mounted along the same axis so that they are parallel a distance d apart. What is the magnetic field at the midpoint of the common axis if a current I flows in the same direction through each coil?
, A proton, deuteron, and an alpha-particle ae all accelerated from rest through the same potential difference. They then enter the same magnetic field, moving perpendicular to it. Compute the ratios of the radii of their circular paths. Assume that md= 2wmp and ma= 4mp.
Is the work required to accelerate a rod from rest to a speed v in a magnetic field greater than the final kinetic energy of the rod? Why?
In Figure P20.65 the rolling axle of length 1.50 m is pushed along horizontal rails at a constant speed v = 3.00 m/s. A resist or R = 0.400 is connected to the rails at points a and b, directly opposite each other. (The wheels make good electrical contact with the rails, so the axle, rails, and R form a closed-loop circuit. The only significant resistance in the circuit is R.) A uniform magnetic field B = 0.800 T is directed vertically downward. (a) Find the induced current I in the resistor. (b) What horizontal force F is required to keep the axle rolling at constant speed? (c) Which end of the resistor, a or b. is at the higher electric potential? (d) Alter the axle rolls past the resistor, does the current in R reverse direction? Explain your answer. Figure P20.65
Is the magnetic field inside a toroid completely uniform? Almost uniform?
The current through a circular wire loop of radius 10 cm is 5.0 A. (a) Calculate themagnetic dipole moment of the loop. (b) What is the torque on the loop if it is in a uniform 0.20-T magnetic field such that p and B are directed at 300 to each other? (C) For this position, what is the potential energy of the dipole?