A 3 m diameter by 4.5 m high tank kept vertically is receiving of density water 1000 kg/m at the rate of 2000 kg/min and is discharging through a 15 cm diameter line with a constant velocity of 1.5 m/s. At a given instant, the tank is half full. Find the water level and mass change in the tank 15 minutes later.

A 3 m diameter by 4.5 m high tank kept vertically is receiving of density water 1000 kg/m at the rate of 2000 kg/min and is discharging through a 15 cm diameter line with a constant velocity of 1.5 m/s. At a given instant, the tank is half full. Find the water level and mass change in the tank 15 minutes later.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 22-cm-diameter solid aluminum sphere (SG = 2.7) is acceleratingat 12 m/s2 in water at 20°C. (a) According to potentialtheory, what is the hydrodynamic mass of the sphere?(b) Estimate the force being applied to the sphere at this instant.
Here, a liquid's density is to be determined by a 1-cm diameter cylindrical hydrometer whose division marks are non visable. The hydrometer is first dropped in water, and the water level is marked. The hydrometer is then dropped into the 'liquid x', and it is observed that the mark for water has risen 0.85 cm above the liquid–air interface. In this case, the height of the originalwater mark is 12.7 cm. As such, how would I determine the density of the liquid?
A cylindrical disk ofwood weighing 45.0 N and having adiameter of 30.0 cm floats on a cylinderof oil of density 0.850 g /cm3(Fig.). The cylinder of oilis 75.0 cm deep and has a diameterthe same as that of the wood.(a) What is the gauge pressure at thetop of the oil column? (b) Supposenow that someone puts a weightof 83.0 N on top of the wood, butno oil seeps around the edge of thewood. What is the change in pressureat (i) the bottom of the oil and(ii) halfway down in the oil?
A thin wire ring, 3 cm in diameter, is lifted from a water surfaceat 20 ° C. Neglecting the wire weight, what is the forcerequired to lift the ring? Is this a good way to measure surfacetension? Should the wire be made of any particular material?
How are large tanks treated in fluid mechanics, conservation mass, conservation momentum and Bernoulli Equation?
A narrow, U-shaped glasstube with open ends is filled with25.0 cm of oil (of specific gravity0.80) and 25.0 cm of water on oppositesides, with a barrier separating theliquids (Fig.). (a) Assume thatthe two liquids do not mix, and find thefinal heights of the columns of liquid ineach side of the tube after the barrier isremoved. (b) For the following cases,arrive at your answer by simple physicalreasoning, not by calculations:(i) What would be the height on eachside if the oil and water had equal densities? (ii) What would the heightsbe if the oil’s density were much less than that of water?
Torricelli’s idealization of effl ux from a hole in the side ofa tank is V = √2 gh, as shown in Fig. P3.81. The cylindricaltank weighs 150 N when empty and contains water at20 °C. The tank bottom is on very smooth ice (static frictioncoeffi cient ζ ≈ 0.01). The hole diameter is 9 cm. For whatwater depth h will the tank just begin to move to the right?
A flotation device is in the shape of a right cylinder, with a height of 0.500m and a face area of 4.00m2 on top and bottom, and its density is 0.400 times that of fresh water. It is initially held fully submerged in fresh water, with its top face at the water surface.Then it is allowed to ascend gradually until it begins to float. How much work does the buoyant force do on the device during the ascent?
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.
A 29-cm-by-47-cm block slides on oil (μ=0.81 Pa-s) over a large plane surface. What force in Newton is required to drag the block at 3 m/s, if the separating oil film is 2 mm thick?
The tank in Fig. is fi lled with water and has a venthole at point A. The tank is 1 m wide into the paper. Insidethe tank, a 10-cm balloon, fi lled with helium at 130 kPa, istethered centrally by a string. If the tank accelerates to theright at 5 m/s 2 in rigid-body motion, at what angle will theballoon lean? Will it lean to the right or to the left?
A skater weighing 500 N skates at 10 m/s and is supported by an averageskating area of 10 cm2. If the viscosity of water is 1 centipoise and the coefficient of friction between skates and ice is 0.02, then find the thickness of the thin film of water existing between the skates and the ice.