Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm. EX 4: Derive an expression for the capillary-height change h, as shown, for a fluid ofsurface tension Y and contact angle 0 be-tween two parallel plates W apart. Evaluateh for water at 20°C if W = 0.5 mm.Widthb intoрарerFig. P1.70

The weight of the water is W=ρVg=ρwbhg The capillarity force is F=γbcosθ The weight of the water…

EX 4: Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate h for water at 20°C if W = 0.5 mm. Width b into раper

EX 4: Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate h for water at 20°C if W = 0.5 mm. Width b into раper

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Related questions

Q: Q3: What force is required to bal ance the weight of the cylinder if the weight of the plunger is…

Q: Drive formula for increas in volume of a thin metalic sphere when if is subjected to an internal…

Q: A) A thin 4-ft-wide, right-angle gate with negligible mass is free to pivot about a frictionless…

Q: A closed vertical cylindrical vessel, 1.80m in diameter, 3m high is 8/10 full of oil (SG=0.85) and…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three…

Q: In a tapered horizontal pipeline, the seawater's speed is 3.75 m/s and the gauge pressure is 21 kPa…

A: The pressure of first point is given as, P1=21 kPa The velocity of first point is given as, v1= 3.75…

Q: 02) A rigid ring A and a rigid thin disk B both made of same material when gently placed on water…

Q: A closed vertical cylindrical vessel, 1.80m in diameter, 3m high is 8/10 full of oil (SG=0.85) and…

A: Given: The diameter of the vessel, d = 1.8 m The height of the vessel, H = 3 m The Specific gravity…

Q: A liquid of density ρ fl ows through a 90 ° bend as shown inFig. and issues vertically from a…

A: Given data: *The density of the liquid is ρ. *The length of the uniform porous section is L m. *Q is…

Q: PROBLEM 2: A rectangular gate rotates about a pivot in the clockwise direction to open. The specific…

A: Given:Specific weight of water, ρg=9.81 kN/m3 or 9810 N/m3Depth of water in the tank, x=10 m

Q: Estimate the resultant force of water on a quadrant gate. It's radius is 1 m and width 2m. The…

Q: The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in…

A: Given data *The length of the water tank, L = 24 cm *The height of the water tank, d = 9 cm *The…

Q: The semicircular plate in the picture is 5 [ft] long and acts as a gate in a channel. The fluid is…

A: Given:

Q: Find the density of a metallic body which flows at the interface mercury of specific gravity 13.6…

Q: the figure, all the fluid are neight H be in cm. essure difference Pa-P_Pa at 20 °C.

Q: Q: The Tank of water in Figure is (12cm) wide in to the paper. If the tank is accelerated to the…

A: Option is B => 30.4 N

Q: watersurface. 1-3 m hinged gate P 3 m

Q: The tank on the truck shown in Figure 1 is completely filled with gasoline,which has a specific…

Q: Two very large open tanks A and F (Fig. ) containthe same liquid. A horizontal pipe BCD, having a…

A: Consider the given diagram: Apply Bernoulli theorem between top of tank A and point D:…

Q: The tank is now moving with constantacceleration up a 30 ° inclined plane, as in Fig..Assuming…

Q: Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm.…

Q: The total weight of the plunger and load is 30 kN, the plunger diameter is D=200 mm. Neglecting…

Q: Calculate the hydrostatic pressure in a reservoir of depth 15 m and density of the fluid is 1000…

Q: Gate ABC is a circular arc, sometimes called a Tainter gate ,which can be raised and lowered by…

A: Given data as per the question radius = 6 m calculations

Q: The 6-ft-radius waterwheel in Fig. is being used tolift water with its 1-ft-diameter half-cylinder…

A: The data given is, The radius of the waterwheel, R = 6 ft Speed of the waterwheel, N = 10 rpm

Q: Watersurface. -3 m hinged. gate P 3 m

A: Given data:-specific weight of water, ω=9810N/m3weight of gate, W=800NNow,length of the gate,…

Q: Find the horizontal and vertical force of water which is effected on the gate as shown in the figure…

A: GIVEN DATA - A QUARTER CIRCLE CURVED SURFACE GIVEN SUPPORTING WATER WE HAVE TO FIND HORIZONTAL AND…

Q: = 2cosa y°i – yx²j V considering the density constant, find an expression for the pressure gradient…

Q: If the wall AB shown is 48 meter long calculate the total force (in the uhlt of KN) on the wall due…

Q: Example: Figure shows a curved surface LM, which is in the form of a quadrant of a circle of radius…

A: Given Data: Radius of the gate = 3 mWidth of the gate = 1mFrom the figure, Distance LO = OM = 3 m

Q: A flotation device with volume = 0.15 m3 and specific weight 1 = 0.27H20 is held submerged in a tank…

Q: ar a gate having quadrant shape of radius 4.5 m carrying water. What will be the resultant force for…

Q: The tank in Fig. 2/is 3 m wide into the paper. Compute the hydrostatic (a) horizontal force…

Q: al, triangular gate with water on one side is shown in Figure. Determine the tota force acting on…

A: Given:width of the traingular gate, b=2 mheight of the triangular gate, h=3 m

Q: Shown below is the free body diagram of a needle floating in a liquid with surface tension o and…

Q: An elliptical gate covers the end of a pipe 4 m in diameter. If the gate is hinged at the top, what…

A: Diameter = 4m water is 8m deep find the normal force F

Q: 1 Calculate the resultant of hydrostatic force on the gate. What vertical force P is necessary to…

A: To find : The resultant of hydrostatic force on the gate and value of vertical force P . Given data…

Q: Hw Pi In a fluid. rotated a r velucity ,Thepressure vise (P)in a radial direction depends upon w, r,…

Q: Q1/ The tank of water in Fig. 1 is (12 cm) wide into the paper. If the tank is accelerated to the…

A: Given that: acceleration = 6 m/s2 Width of the tank = 12 cm It is required to determine: (a) Depth…

Q: If the wall AB shown is 48 meter long calculate the total force (In the uhit of KN) on the wall due…

Q: An open cylinder tank, D= 1.0m, h=1.5m, contain water at depth 1.0m. If this tank rotate about its…

A: Given data:

Q: In the figure shown, what the minimum height (h) t which water must rise in th water tank in order…

Q: A fi sh tank 14 in deep by 16 by 27 in is to be carried in acar that may experience accelerations as…

A: The depth of the fish tank is d=14 in. The length of the fish tank is l=27 in. The width of the fish…

Q: Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2…

A: Given Data: The radius of the water droplet is r=15 mm=0.015 m The excess pressure inside the…

Q: 1.2 m and diameter 0.6 m is three quarters filled with water when stationary. If the tank is rotated…

Q: An elliptical gate covers the end of a pipe 4 m in diameter. If the gate is hinged at the top., what…

Q: The parabolic shaped gate with a width of 6 m shown below is hinged at point B. Compute for the…

A: The pressure exerted by the fluid at a point which is located at a depth of h from the surface is…

Q: The rectangular gate CD is 1.8 m wide and 2 m long as shown in the figure below. Water 2.0 m 2.0 m…

Q: Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in Figure QI (a), can float…

A: The surface tension of water at 20 degrees Celsius is 0.072 N/m.

Q: Problem 2. In reference to the figure, gate XY is 1.20m wide and 1.40m long. If the liquid in the…

Q: 3. For the gate shown, a = 45°, Y₁ = 1 m, and y₂ = 4 m. Will the gate fall or stay in position under…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.

EX 4: Derive an expression for the capillary-
height change h, as shown, for a fluid of
surface tension Y and contact angle 0 be-
tween two parallel plates W apart. Evaluate
h for water at 20°C if W = 0.5 mm.
Width
b into
рарer
Fig. P1.70

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the standard sea level density (p) in slugs/ft^3?
A rectangular car is 3 m. long by 1.5 m wide and 1.5 m deep. If friction is neglected and the car rolls down a plane with an inclination of 20 degrees, what is the inclination of the water surface if the car contained 0.60 m depth of water when the car was horizontal?
The fuel gage for a gasoline tank in a car reads proportionalto the bottom gage pressure as in Fig. . Ifthe tank is 30 cm deep and accidentally contains 2 cmof water plus gasoline, how many centimeters of airremain at the top when the gage erroneously reads“full”?
If the pressure in the air space above an oil (s=0.75) surface in closed tank is 200 Kpa absolute, what is the gage pressure 4 meter below the surface?
A hydrometer fl oats at a level that is a measure of thespecifi c gravity of the liquid. The stem is of constant diameterD , and a weight in the bottom stabilizes the body tofl oat vertically, as shown in Fig. . If the positionh = 0 is pure water (SG = 1.0), derive a formula for h as afunction of total weight W , D , SG, and the specifi c weightγ 0 of water.
6.At sea level a mercury barometer reads 750 mm and at thesame time on the top of the mountain another mercury barometer reads 745 mm. If the specific weight is uniform at 12 N/m3, determine the height of the mountain. Fluid Mechanics
Any pressure reading can be expressed as a length or head,h = p / ρ g . What is standard sea-level pressure expressed in( a ) ft of glycerin, ( b ) inHg, ( c ) m of water, and ( d ) mm ofethanol? Assume all fl uids are at 20 ° C.
3. A barrel contains a 15 cm layer of oil of density 5.88 kN/m3 floating on water that is 30 cm deep. What is the gauge pressure in mmHg at the oil-water interface?
Q3)A tank 6 m long 3 m wide and 2 deep contains oil to depth of 1.75 m .If it accelerated horizontally at 2.5 m/s2 in the direction of its length. How muchı oil would spill out and the acceleration force.
A closed cylindrical vessel, 2m in diameter & 4m high is fully filled with water & rotated to its vertical axis at a constant speed of 12.2 rad/sec. The top is pressurized by 180 KPa. (a) What is the pressure at the center bottom of the cylinder? (b) What is the pressure at the circumference bottom of the cylinder? (c) What is the total hydrostatic force at the sides of the cylinder?
A block with specific gravity of SG= 1.45 and volume V= 0.75m3, is attached to a spring scale. The block is hung vertically such that it is fully submerged in oil ρoil= 0.85kg/m3 . a) Draw a free body diagram for the block. b) What is the apparent weight of the block?
A hemispherical container, 26 inches in diameter, is filledwith a liquid at 20 ° C and weighed. The liquid weight isfound to be 1617 ounces. ( a ) What is the density of thefluid, in kg/m 3 ? ( b ) What fluid might this be? Assume standardgravity, g = 9.807 m/s 2 .