a. In sequence networks of power system, why does voltage sources appear only in the positive sequence? b. Describe the main differences in fault protection objectives when dealing with a temporary fault vs a permanent fault.

a. In sequence networks of power system, why does voltage sources appear only in the positive sequence? b. Describe the main differences in fault protection objectives when dealing with a temporary fault vs a permanent fault.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.35P

See similar textbooks

Related questions

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Line to ground fault has the highest probability in the power system O True False

A: Need to find true false

Q: Two alternators rated 15 MVA and 20 MVA have per unit reactance of 0.20 and 0.60 respectively are…

A: In this question, Two alternators rated 15 MVA and 20 MVA have per unit reactance of 0.20 and 0.60…

Q: Q2. Explain the symmetrical fault analysis using ZbuS.

A: Note: As per the guidelines will be solving only 1st question. Repost for others Symmetrical fault…

Q: Which among the following faults does mostly happen in 3-phase power systems? Single line to ground…

A: As 3 phase fault in power system are, 1. Single Line to Ground fault 2. Three phase short circuit 3.…

Q: 3.On a double line-to-ground faultImmersive reader A) The short-circuit currents in the faulted…

A: In this question , we will write about double line to ground fault....

Q: A 500-MVA 20-kV, 60-Hz synchronous generator with reactances X, = 0.15, X: 0.24; X 1.1 per unit and…

Q: Explain fault analysis in power system by fuzzy logic or artificial neural networks with neat…

A: Artificial Neural Network (ANN) or Fuzzy logic can be applied to the power system fault analysis…

Q: The following figure shows the single-line diagram of a three-bus power system. Additionally, a…

A: y23=-j20-j25 =-j45 If three phase fault occurs at bus 3

Q: A short circuit occurs in the series R-L circuit with V = 20 kV, X = 8 ohm, and R = 0.8 ohm. The…

A: Given V- 20 kV R= 0.8 ohm X= 8 ohm

Q: 1. The number of devices required to perform the no-load test and the short-circuit test for…

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: For the system shown below, each generator has positive, negative, and zero sequence reactances of 3…

A: given for generator positive,negative and zero sequence impedance are =3 ,2 and 1 ohm for…

Q: Let the system of Figure 1 operating with mechanical input Pm at a steady angle ĉo. A three phase…

A: If a fault occurs in the system, δ begins to increase under the influence of positive accelerating…

Q: 8.In a line-by-line failure we can expect Immersive reader A) Currents exist in the ground…

Q: For the system shown below, each generator has positive, negative, and zero sequence reactances of 3…

A: You have asked multiple independent questions. We are authorized to answer one question at a time.…

Q: What type of fault is phase to phase fault in power system.(Symmetrical or Unsymmetrical). Discuss…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: I. Draw the reactance diagram for the following power system in per unit using base power = 50 MVA…

Q: 5. The positive sequence network, negative sequence network and zero sequence network are shown in…

A: It is given that: Zf=0.05

Q: The magnitude of the fault current depends on the generator and fault impedance and ________________…

A: The magnitude of fault current depends on voltage at fault point and impedance upto fault point…

Q: 96\ Derive equations of critical clearing angle and time for a symmetrical three-phase fault at…

Q: 2. Explain how the value of fault current can be computed for L-L-G fault occurring at the unloaded…

Q: fault current

A: Given- Sequence→ Positive Negative Zero Generator 0.16j 0.16j 0.06j Transformer-1 0.1j 0.1j 0…

Q: b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

A: POWER SYSTEM: A power system is a network of electrical components that provide, transmit, and…

Q: A fault which gives rise to symmetrical fault currents (equal faults currents with 120-degree…

A: Symmetrical fault: When three phase lines are balanced, when ever a fault occurs betwe these lines…

Q: Critical clearing time of a fault in power system is related to steady state stability limit True…

A: Critical clearing time is the maximum time that is allowed to remove the disturbance without…

Q: Problem 1(B)- If the fault in Problem 1(A) was a Line-Line fault between phases B and C through a…

Q: three phase generator with constant terminal voltages gives the following currents when under fault:…

A: The solution can be achieved as follows.

Q: Consider the multi-terminal line in the system shown below. Each of the buses C. D, G, H and J has a…

A: Consider the multi-terminal line in the system as shown below, Where, every one of the buses C, D,…

Q: What is subtransient and transient fault current? How do they occur in a system?

A: In a system before the fault occurs voltage and current both are symmetrical AC but when a 3 phase…

Q: The one-line diagram of a simple power system is shown in the figure. The neutral of each generator…

Q: Two alternators rated 30 MVA and 20 MVA have per unit reactance of 0.30 and 0.50 respectively are…

A: The single line diagram of the given system is shown below: Let the base power be 30 MVA, the…

Q: (b) Explain the steps involved in analysing balanced bolted fault in power system using Zbus method,…

A: Admittance matrix and impedence matrix is very important to analyze the power system .Admittance…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

Q: A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: FIGURE Q2 shows a four bus three phase power system. The generators, transformers and transmission…

Q: In a 3 phase, 3 wire system, it has normal voltage of 10.4kV line to line fault occurs at generator…

A: For the 3- phase line to line the positive sequence phase current is evaluated as:

Q: A three-phase short circuit occurs at point P for the system shown in the following figure. (a)…

A: In this solution, we'll discuss about pu impedance diagram & fault analysis of a power system.

Q: The speed of circuit breaker is defined as the time between the occurrences of the fault to the…

A: Given The speed of circuit breaker is defined as the time between the occurrences of the fault to…

Q: 3-phase, 33-MVA, 44-kV alternator has a substransient reactance of 7%. A 3-phase short circuit…

A: Given s=33-MVAV=44-KVsubtransient reactance=7%=0.07P.U

Q: The reactance information of the power network is shown in the figure, in units of common base. The…

Q: 1. A three-phase short-circuit fault occurs at point F in the system shown. Calculate the p.u. fault…

Q: Given the network shown, for a solid three-phase fault on bus 2 (a) find the sub transient current…

Q: Q1. All Choose the correct answer: 1. One of the advantage of using a per unit system in power…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: What type of fault is phase to phase fault in power system.(Symmetrical or Unsymmetrical). Discuss…

A: The explanation is as follows.

Q: Contribution of fault analysis in power system netwrok?

A: Solution- Contribution of fault analysis in power system network- Fault analysis of a power system…

Q: A protection system engineer is planning to provide the complete protection, he can achieve this by…

A: A protection system engineer is planning to provide the complete protection.

Q: 1- Which of the following is true in decoupled load flow method a- Jacobians J1 and J2 are…

Q: A 100-MVA, 18-kV generator is connected to a transformer. The generator has reactances of 19%, 26%…

A: Given: S=100 MVA VLmax.=18 kVReactances-Xd''=19% , Xd'=26% , Xd=130%Time constants-Td''=0.035 sec ,…

Q: The per unit values of positive, negative and zero sequence reactances of a network at fault are…

A: For double-line to ground fault, Vb=Vc=0Ia=0 Let the fault phases are b and c, then The positive,…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

answer both i will rate....

a. In sequence networks of power system, why does voltage sources appear only in the positive sequence?

b. Describe the main differences in fault protection objectives when dealing with a temporary fault vs a permanent fault.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A three-phase circuit breaker has a 15.5-kV rated maximum voltage, 9.0-kA rated short-circuit current, and a 2.50-rated voltage range factor. (a) Determine the symmetrical interrupting capability at 10-kV and 5-kV operating voltages. (b) Can this breaker be safely installed at a three-phase bus where the symmetrical fault current is 10 kA, the operating voltage is 13.8 k V, and the (X/R) ratio is 12?
Consider the oneline diagram of a simple power system shown in Figure 9.20. System data in per-unit on a 100-MVA base are given as follows: The neutral of each generator is grounded through a current-limiting reactor of 0.08333 per unit on a 100-MVA base. All transformer neutrals are solidly grounded. The generators are operating no-load at their rated voltages and rated frequency with their ENIFs in phase. Determine the fault current for a balanced three-phase fault at bus 3 through a fault impedance ZF=0.1 per unit on a 100-MVA base. Neglect -Y phase shifts.
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Equipment ratings for the four-bus power system shown in Figure 7.14 are as follows: Generator G1: 500 MVA, 13.8 kV, X=0.20 per unit Generator G2: 750 MVA, 18 kV, X=0.18 per unit Generator G3: 1000 MVA, 20 kV, X=0.17 per unit Transformer T1: 500 MVA, 13.8/500YkV,X=0.12 per unit Transformer T2: 750 MVA, 18/500YkV,X=0.10 per unit Transformer T3: 1000Â MVA, 20/500YkV,X=0.10 per unit A three-phase short circuit occurs at bus 1, where the prefault voltage is 525 kV. Prefault load current is neglected. Draw the positive-sequence reactance diagram in per unit on a 1000-MVA, 20-kV base in the zone of generator G3. Determine (a) the ThĂ©venin reactance in per unit at the fault, (b) the subtransient fault current in per unit and in kA rms, and (c) contributions to the fault current from generator G1 and from line 1-2.
Describe the concept of fault current analysis in power systems and its role in protecting electrical equipment.
Describe the concept of "fault current" in power systems. How is fault current calculated, and what measures are taken to protect equipment and personnel from high fault currents?
Explain the concept of fault analysis in power systems. What are the different types of faults, and how are they analyzed and mitigated?
Discuss the concept of fault analysis in power systems. What are the types of faults and their effects?
Describe the process of fault current analysis in power systems and its significance in protecting electrical equipment from damage.
Discuss the concept of fault analysis in power systems and the types of faults that can occur.
Explain the concept of fault analysis in power systems. How is fault current calculated, and what protection mechanisms are in place?
Discuss the concept of fault analysis in power systems and the techniques used to identify and locate faults in electrical networks.