A 3-phase transformer connected to a load. The following per-phasevalues are given:Reg.s = 1.2 Ohms,Xeg,s = 2.2 Ohms,eq,sRc.s= 1460 Ohms,XM.s= 880 Ohms.The current I= 84.5 36.87 A.andP = 161836.87°Volts.Find the Copper and the core losses in this 3-phase transformer.

we need to determine copper loss and core loss for the given 3 phase transformer

A 3-phase transformer connected to a load. The following per-phase values are given: Req.s = 1.2 Ohms, X egs = 2.2 Ohms, Rcs= 1460 Ohms, %3D XM.s= 880 Ohms. M,s The current I,=84.5 -36.87°, A,and P= 1618 /-36.87° %3D Volts. Find the Copper and the core losses in this 3-phase transformer.

A 3-phase transformer connected to a load. The following per-phase values are given: Req.s = 1.2 Ohms, X egs = 2.2 Ohms, Rcs= 1460 Ohms, %3D XM.s= 880 Ohms. M,s The current I,=84.5 -36.87°, A,and P= 1618 /-36.87° %3D Volts. Find the Copper and the core losses in this 3-phase transformer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.63P: A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a...

See similar textbooks

Related questions

Q: B. A 10-kVA, 2300/230-V transformer is to be tested to determine its excitation branch components,…

A: 10KVA voltage 2300/230 V Open circuit test parameters given Voltage regulation of 0.8 lagging power…

Q: A 50 Hz, 1-phase transformer has a turn ratio of 6. The resistances are 0.9 ohm and 0.03 ohm and…

Q: B. A 10-kVA, 2300/230-V transformer is to be tested to determine its excitation branch components,…

A: Given : kva = 10 V base= 2300 Voc= 2300 v Ioc= 0.2 A Poc= 40 w Vsc= 48 v Isc= 5 A Psc= 180 w

Q: 1. Design a 150VA power, 240V input, 48V and 12V single-phase transformer. G:25 mm, E: 12.5 mm, F:…

A: Given: The rating of a single-phase transformer is 150 VA, 240 V/48 V-12 V where G:25 mmE:12.5…

Q: The circuit for a 20-KVA, 220/3960 V, 50-Hz transformer is shown in Figure (1). The open- circuit…

Q: 3. A 100 KVA, 4000V / 200V, 50 Hz single phase transformer has 100 secondary tu Determine (a) the…

A: In this question , we will find currents in both windings , turn and maximum flux..

Q: A 2300/208-V 500-kVA 60-Hz single-phase transformer was tested by means of the open-circuit test (on…

Q: A 2000-kVA, 6,600/400-V, 3-phase transformer is delta-connected on the high voltage side and…

A: Given Data: Transformer rating : 2000-kVA, 6,600/400-V, 3-phase Full load pf = 0.8 Short circuit…

Q: 23/A) A 1000-VA 230/115-V transformer has been tested to determine its equivalent reunt. The results…

Q: 2. A 2000-VA 230/115-V transformer has been tested to determine its equivalent circuit. The results…

A: The open-circuit test and short-circuit test data of a 2000 VA, 230/115 Volts transformer is given…

Q: The primary winding of a transformer has a terminal voltage of Vsource = 240 V. The turns ratio of…

Q: A 2000-kVA, 6,600/400-V, 3-phase transformer is delta-connected on the high Example voltage side and…

Q: Following measurements are acquired at a no load operation of a one phase transformer; Input Voltage…

Q: 4.32 Consider a 75 kVA, 2400/240 V, 60 Hz transformer. Assume that the open-circuit and short-…

Q: Explain the origin of negative voltage regulation in a transformer. Derive the equation of no-load…

A: We will answer both subparts. It is asked to explain the origin of negative voltage regulation in a…

Q: A 10 KVA, 120/600 V, 60 Hz, single- phase transformer is tested with the following results: Find the…

A: According to the question we need to calculate the value of Req, Xeq.

Q: Q.1: The following data refer to a single-phase transformer: Turn ratio (1:5), R1=0.24 n, X=1 N,…

Q: Q2. A 25-kVA, 2300:230-volt transformer is subjected to open- and short-circuit tests. The…

A: To determine the transformer circuit parameters and efficiency of the machine there are two types of…

Q: A 30 KVA, 24000/220 V, Y A connected transformer bank is operated at full load with an efficiency of…

A: Given S =30 KVA V1 =24000∠0° VV2 =220∠-5.77° V Efficiency η =96% Voltage regulation =11% Primary…

Q: A 10-kVA, 440/3300-V, 1-phase transformer, when tested on open circuit, gave the following figures…

Q: (a) A single-phase mutual induction, transformer has a nameplate rating of 2500 VA, 230V-115V.…

Q: a step-down transformer of 23 kVA, 2300 V / 230 V, 50 Hz, R1 = 4 Ω, X1 = 12 Ω, R2 = 0.04 Ω, X2 =…

A: a) Calculate the rated current by substituting the values of V=230 V, P=23 kVA in the power…

Q: Data obtained from short circuit & open circuit tests of 60 kVA, 3200-220 V are: Open circuit:…

Q: Q3/A) A 1000-VA 230/115-V transformer has been tested to determine its equivalent circunt. The…

A: given that VOC=230VIOC=0.45APOC=30WPOC =VOCIOCcosϕ∘cosϕ∘=POC VOCIOC=30230×0.45=0.289POC =VOC2RC⇒…

Q: 15. A 10-kVA, 200-V/400-V, 50-Hz, single-phase transformer gave the following test- results : OC…

Q: Q4/ The equivalent circuit impedances of a 20-kVA, 8000/240 V, 60-Hz transformer are to be…

A: I am attaching detailed solution image of this question.

Q: A 1-ph transformer 25kVA, 330/110V, 50Hz, Req2 = 0.04522 and Xeq2 = 0.0650 draw the Kapp regulation…

A: Single Phase Transformer: An electrical device that accepts single-phase alternating current and…

Q: A 500 kVA, 2300/230 V, 60 Hz transformer was open- and short-circuit tested. The data is provided…

Q: Problem 2: Transformer circuit 1H R V mains 10 A transformer has a winding that has the equivalent…

A: NOTE: : Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: QA/ A 50 KVA, 2300/230 V, 60 Hz transformer has a high voltage winding resistance of 0.65 W and a…

A: Given : P0 = 50 kVA, V1 = 2300V , V2 = 230V, f = 60 Hz R1 = 0.65 Ω (H.V. Side), R2 = 0.0065Ω…

Q: Q-2-c) The equivalent circuit impedances of a BK-VA, 6350/220-V, 50-Hz transformer are to be…

Q: Q3/A/ The equivalent circuit impedances of a 20-kVA, 8000/240 V, 60-Hz transformer are to be…

Q: A low voltage distribution transformer feeds two different loads with a three-phase line. The…

A: Given Data is- Nominal Voltage V=400 volt The total length of the feeder L=500 m…

Q: Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The…

Q: Q2. A 25-kVA, 2300:230-volt transformer is subjected to open- and short-circuit tests. The…

A: Transformer: Transformer is a static electrical device which transfers power from one circuit to…

Q: A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are…

Q: Q10) For the transformer shown in Figure below, determine (i) The turns ratio of the transformer…

A: A transformer has two windings - the primary and the secondary. The ratio of the number of turns in…

Q: (nter -Tapped Trenformer DI Rs Vs = 40 11 N. = 2 VS NS1 %3D Np Nz= 10 Rs =30 RL- 300 RL %3D Vs is…

Q: A 900-VA 230/115-V transformer has been tested to determine its equivalent circuit. The results of…

A: Given data, VOC=230 VIOC=0.45 APOC=30 WVSC=19.2 VISC=8.9 APSC=42.5 W

Q: A 19-KVA, 829V/601V, 50-Hz, a single-phase transformer has the following parameters as referred to…

A: In this question we need to find a voltage regulation of the transformer.

Q: Q1) The equivalent circuit impedances of a 20-kVA, 8000/240 V, 60-Hz transformer are to be…

Q: A 3-phase transformer connected to a load. The following per-phase values are given: Regs = 1.2…

A: According to question we need to calculate the value of copper loss and core loss.

Q: 3- The approximate equivalent circuit of a 20KVA, 8000/240 V, 60 iz transformar is to be determined.…

Q: 1. A 1000-VA 350/140-V transformer has been tested to determine its equivalent circuit. The results…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results…

A: Transformer of 1000 VA,230/115-v Open circuit test(secondary side)Voc=115 vIoc=0.11 APoc=3.9 wShort…

Q: A short-circuit test is carried out on a single-phase, 10 MVA, 66 kV/7.2 kV transformer T as shown…

A: Given information: The value of the rated primary current is:

Q: 9. A 10-kVA, 2000/400-V, single-phase transformer has resistances and leakage reactances as follows:…

A: Given, Primary voltage, V1 = 2000 V Secondary voltage, V2 = 400 V So, transformation ratio,…

Q: Question 3: Design an isolated transformer to energise Load at the below circuit. The Load power is…

A: Electrical machines can be either generator , transformers or motors. They can be either Ac machines…

Q: Consider the following open circuit transformer as shown in figure below which operate at: the…

Q: A 10 kVA, 1000/250 V transformer is to be tested to determine its equivalent circuit parameters. The…

A: 10KVA transformer 2000/250V Open and short circuit parameters Given Equivalent circuit? Copper…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

A 3-phase transformer connected to a load. The following per-phase
values are given:
Reg.s = 1.2 Ohms,
Xeg,s = 2.2 Ohms,
eq,s
Rc.s= 1460 Ohms,
XM.s= 880 Ohms.
The current I= 84.5 36.87 A.and
P = 1618
36.87°
Volts.
Find the Copper and the core losses in this 3-phase transformer.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
A 250/125 V, five kVA single-phase transformer has a primary resistance of 0.2 ohms and reactance of 0.75 ohms. The secondary resistance is 0.05 ohm and reactance of 0.2 ohms.a) Determine its regulation while supplying full load on 0.8 leading p.f.b) The secondary terminal voltage on full load and 0.8 leading p.f.Ans.: -0.4.88%; 131.1
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
The efficiency of a transformer at load 0.8 p.f. Lag is -- at load 0.8 p.f. Lead * equal less than more than none of these
The resistance and reactance of the primary winding of a 440/110 V single phase transformer are 4.4 ohm and 8 ohm respectively. The resistance and reactance of the secondary winding are 1.6 ohm and 2ohm respectively. Then find the equivalent resistance, reactance and impedance referred to the primary side.
A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and secondary resistances are 0.55 ohm and 0.035 ohm respectively. The corresponding leakage reactances being 4.22 ohm and 0.18 ohm. The load is equivalent to a coil of resistance 3.85 ohm and inductive reactance of 4.2 ohm. Determine the terminal voltage of the transformer and the output in kW when supplying a given load using approximate equivalent circuit when the applied voltage is 7912 V. Your answer
10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and the number of turns of the low voltage winding is N2=34. The high voltage winding is energized with V1= 10 kV rms line-to-line and V2= 400 V rms line-to-line has been taken from the low voltage winding. What is the connection of the low voltage winding if the high voltage winding is Y-connected? Εισαγάγετε την απάντησή σας
The primary ofa certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
B)- various losses in transformer. Explain how each loss varies with load 11=ph=v! Phovl Describe current, supply voltage.