A 3-phase,16 pole alternator has a wye connected full-pitch with144slots and 10 conductors per slot all in series. The flux per pile is0.04 Wb sinusoidally distributed at 60HZ. What is the no-load emfbetween the lines.Choices:A. 1841 VB. 2455.14 VC. 4252.43VD. 3289 V.A 4-pole,3-phase,60HZ, wye connected alternator has 24 slots with 40turns in each coil and sinusoidally distributed flux per pole of 63mWb.What is the terminal voltage an open circuit if the pitch factor is unity.Choices:A. 4449 VB. 4439 VC. 4943VD. 4493 V

Answered: Image /qna-images/answer/2228fb79-6214-4c4d-8cfa-c095f826bb2a.jpg

A 3-phase,16 pole alternator has a wye connected full-pitch with 144slots and 10 conductors per slot all in series. The flux per pile is 0.04 Wb sinusoidally distributed at 60HZ. What is the no-load emf between the lines. Choices: A. 1841 V B. 2455.14 V C. 4252.43V D. 3289 V.

A 3-phase,16 pole alternator has a wye connected full-pitch with 144slots and 10 conductors per slot all in series. The flux per pile is 0.04 Wb sinusoidally distributed at 60HZ. What is the no-load emf between the lines. Choices: A. 1841 V B. 2455.14 V C. 4252.43V D. 3289 V.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Related questions

Q: If R1 is in series with a parallel combination of R2, R3, and R4, when the resistance value of R2 in...

A: This question belongs to circuit theory . It is based on the dependency of voltage and current on th...

Q: Problems A 25-hp 240-V 77.8-A shunt motor has an armature resistance of 0.083 N and a field-circuit ...

Q: 7-15 An FM tone-modulated signal has a frequency deviation of 12 kHz and a modulating froquency of 2...

A: This question belongs to basic communication system . It is based on the concept of FM tone modulat...

Q: Find inverse Laplace transform of 10 F(s) = (s + 2)(s² + 6s + 10)

Q: Q3 Given z,=(3+j4)² and z,= 2.5jej40x a. Find z¡+Z2 b. Find the magnitude and phase of z,z2

A: Given Z1=(3+j4)2 Z2=2.5ej40π

Q: How much is the service charge? 2. How much is the energy charge subtotal? 3. How much is the dema...

A: Here, we have to find the following values, 1. The service charge 2. The energy charge subtotal 3. T...

Q: Determine ?1to ?5.

A: The given circuit is shown below:

Q: 15 KVA closet transformer lovated inside a building is used to step down the voltage for the buildin...

Q: ЧА Cz

Q: It's the weekend, Kim Jong Un's hackers crashed the internet, you are in a COVID lockdown with the n...

Q: Compute the charge stored on a 4-pF capacitor with a 24V across it.

A: The charge stored in a capacitor, Q in coulomb as the product of the capacitance C (in Farads) of th...

Q: 50.43 3 (1.25) (1.25) 103.75 300 10.9 (1.25) +► (7.77) (1.25) 249.58 90.51 136.93 <- (18.42) 126.03 ...

Q: 1. Assuming the spherical D- layer has a refractive index of 0.8, and the frequency of transmitted s...

A: As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the separate...

Q: Vc Given: vCC = + 15.00 v RC VBB = + 5.00 V VBE = 0.72 V RB VBB VB = 1.20 V RC = 3.20 kOhm RE BDc = ...

A: Brief description : In the given question they have mentioned a bipolar junction transistor common e...

Q: 3. Refer to the circuit shown C 120V, 60HZ Z = 10+j12 2 (a)What is the power factor? (b) What is the...

Q: 5. Find Io in the circuit of Fig. 1.33. ww 1, -j22 j6 2 ww 60-30° V 10Ω Fig. 1.33

A: This question belongs to circuit theory . It is based on the concept of calculation of equivalent im...

Q: Please find I and V values (Diodes are made of Si).

A: The given circuit is shown below:

Q: 2. Two empty capacitors, C1 and C2, are connected in series with R1. The capacitance of C1 is 2F, th...

A: We need to find out voltage and charge across capacitor in given circuit

Q: 1. What is the difference between Miswire and short in the cabling?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source, eithe...

Q: find the output waveform for the circuit in figure (3) JAP Ivin3D4 sin wt VR 2V Figure (3)

A: In open loop opamp acts as comparator and output switches between saturation values. If voltage at n...

Q: Determine the Thevenin equivalent network at teri

Q: 5) Determine if this transfer function can be approximated by a 2nd Order system 1 G(s) = (s2 + 16s ...

Q: Please convert the ff. breadboard circuit into a circuit diagram

Q: An inductive coil with a resistance R and inductance L is connected in parallel with a 30 ohm resist...

Q: The magnetic field intensity in free space is H=25cos(βz+20000t)ay A/m. Find a) The phase constat b...

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part ...

Q: The resistors in the figure have length and cross-sectional area and are made of material with the s...

A: We can find the resistance of a given material with the below given formula. R = pl/a. p = resistivi...

Q: A 100kVA,6600/330 V , 50Hz, single phase transformer takes a current of 10 A, 43 W at 100V in a shot...

A: It is given that: S=100 KVAPsc=43 WIsc=10 AVsc=100 Vcosθ=0.8

Q: a) What is this circuit? b) Is there an RF signal across R2? c) Draw the expected signal waveform ac...

A: Given the circuit, as shown below: a) We need to explain what is the circuit. b) We need to explain...

Q: 1 Obtain C(0.5), C(1.5) and C(2.5) under unit impulse input using the modified z-transform. (T=1) R(...

A: The block diagram is shown below,

Q: 2kN 0.3V 0.004Vo 251 40k . 10kN. Vo +

Q: A coil of resistance of 15 ohms and inductance 0.05 H is connected in parallel with a non-inductive ...

Q: Solve the energy stored in capacitor.

A: In this question, We need to determine the energy stored in the capacitor? We know energy stored i...

Q: Construct the equivalent circuits using logic gates and explain your answer. There are two teams...

A: Given, There are two groups namely group A and group B. Both groups have two members, a member of gr...

Q: Explain anyone practical measurement system with all of its functional elements

A: The practical measurement system includes modern measuring instruments such as multimeter, oscillosc...

Q: For the following circuit, find the CMRR the common mode rejection ratio in dB [ 20 Log() ], for Vo ...

A: The common-mode rejection ratio (CMRR) of an op amp is the proportion of common-mode gain to differe...

Q: 1)-What happens if different voltage and different current ratings of solar panels are connected tog...

A: (i) Panels of the different voltage and different current ratings are connected in series. The out...

Q: Which of the following integrations finds the flus exiting the closed surface r= 5 for the vector fi...

A: Magnetic flux- It is defined as the number of magnetic line passes through a closed surface.

Q: In a certain silicon diode, it was found that the diode current is 15mA when the diode voltage is 0....

A: Here, we have a Si diode at room temperature. The diode current, ID1=15 mA The diode voltage, VD1=0....

Q: Explain the working of Magnetic Tape type recorder with a neat diagram.

A: Magnetic tape- The magnetic tape is coated with a material (iron oxide or chromium dioxide) that ten...

Q: 9. A sif X(1) = Am COS(2 Jm1) a si Ac (2Tfc1) iñn a double-sideband transmitted-carrier (DSBTC) syst...

A: We need to find out the power for given amplitude modulated signal

Q: A 415V, 3-phase Induction motor has output of 30HP and operates at power factor of 0.6 lagging with ...

A: The information we have : Output power, Pout=32 hp=32×746 Watts=22380 Watts Power factor, cosϕ= 0.6...

Q: 2kΩ I 0.3V 0.004Vo 251 40kN 10kΩ Vo Figure 2 + +

Q: 1. In the system in Figure E.1, x,(t) = sinc(t), fc = 10 and the cutoff frequency of the lowpass fil...

A: Given the system a shown below: xt(t)=sinc(t), fc=10 and the cut-off frequency of the low-pass filt...

Q: Write solutions neatly so I can understand. Thankyou very much! guaranteed thumbs up !!!!

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines o...

Q: A 33-kohm resistor is connected in series with a parallel combination made up of 5.6-kohm resistor a...

Q: Auto Light Switch

A: Automatic Light Control - Automatic Lighting Control ideally is to control the lights even when one...

Q: 7-11 A90-MHz carrier is to be frequency modulaled by a 2-kHz tone. The maximum frequency deviation i...

A: Brief description : Modulation technique is one of the major advantage which is exist in the communi...

Q: Define Attenuation and find the attenuation at the destination if the power at the destination is 10...

A: Attenuation : Attenuation is loss of signal strength in networking cables and connections. Attenuati...

Q: We want to install the 2000-meter wire in the college building, which one testing is the most import...

A: Here, we required to install the 2000-meter wire in the college building.

Q: determine IB and VE

A: The value of base current and emitter voltage can be obtained from DC analysis.

Concept explainers

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.

Question

A 3-phase,16 pole alternator has a wye connected full-pitch with
144slots and 10 conductors per slot all in series. The flux per pile is
0.04 Wb sinusoidally distributed at 60HZ. What is the no-load emf
between the lines.
Choices:
A. 1841 V
B. 2455.14 V
C. 4252.43V
D. 3289 V.
A 4-pole,3-phase,60HZ, wye connected alternator has 24 slots with 40
turns in each coil and sinusoidally distributed flux per pole of 63mWb.
What is the terminal voltage an open circuit if the pitch factor is unity.
Choices:
A. 4449 V
B. 4439 V
C. 4943V
D. 4493 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two 15-kVA, 400-V, 3-ph alternators in parallel supply a total load of 25 kVA at 0.8p.f. lagging. If one alternator shares half the power at unity p.f., determine thep.f. and kVA shared by the other alternator.
The terminal voltage of a 3-φ generator is 19053 V, line-to-line. The load draws a current of 1515 A, leading, with a phase angle of 30o. The total real power, drawn by the load would be:
In the figure, the circuit is given as VRS =√3 . 60V and Zy = 6 + j8. Find the value of C to be connected in order to make the power drawn from the system in a phase 1, to make the load current 1, and to make cos(φ) 1.
A 3 phase synchronous generator has a synchronous reactance Xs of 9 Ω perphase, a no-load line to neutral AC voltage E of 12 kV and a line to line terminalvoltage of V of 17.3 kV.(a) Derive the formula for the 3 phase power produced by the generator in terms ofthe power angle δm, |V |, |E|, and Xs. (δm is the angle between E and V ).(b) The power angle δm = 30 degrees. Calculate the 3 phase real power delivered to thegrid at the terminals of the generator.(c) The real power increases when the power angle δm increases, but there is amaximum possible theoretical power that the generator can produce. Calculate themaximum 3 phase real power. Solve A-C
Suppose an AC generator with V(t) = (150V)sin(100t) is connected to a series LRC circuit with R=40 Ohm, L=80 mH, and C=50 microFarad, as shown in figure. Calculate the maximum voltage across the resistor (VR0)?
Calculate ZL for maximum average power transfer in the circuit, and find the maximum average power delivered to the load. The given answer is ZL=2-j2 Ω, PL=45 W
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
A shunt generator has a load of 5.9kw at 143V and it is supplied by a pair of feeder conductor with resistance of 0.09ohm each. Ra=0.12, Rsh=69 ohms. The generated emf is?
Given:1. 10 Pole, wye-connected three-phase alternator2. 240 slots 3. 4 turns per coil (lap coils)4. 16/24 pitch5. 8460000 maxwell flux per pole6. 1670 rpm, alternator driven speed Determine the total line - to - line generated voltage. Please show the detailed formula and solution.
An unbalanced delta-connected load is supplied from a 400-V, 3-ph, delta-connected alternator through conductors having impedances of 4 + j3 ohms. The load consists of Zab = 15<30 ohms, Zbc=30<45 ohms and Zca = 30<60 ohms. There is no neutral connection. The phase sequence is ABC with Eca as the reference phasor. Determine the line currents and the voltage between the star-point of the alternator and that of the load. Express your answers in polar form.
Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 + j3 and 2 + j4.5 ohms are connected in parallel to a 7900-V source. Their secondaries are supplying a common load of 30 + j40 ohms. What is the magnitude of the voltage across the load in volts? (2 decimal places)
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.