A 30 m steel tape weighing 1.45 Kg is of standard length under a pull of 5 Kg,supported for full length. This tape was used in measuring a horizontal line AB whichis 735.15 m long on smooth level ground under a steady pull of 8 Kg. Assuming E = 2x 10^6 Kg/cm^2 and the unit weight of the steel is 7.9 x 10^-3 Kg/cm^3. It was laternoticed that the measurements were performed on a sloping ground (gentle slopeonly) and the difference in elevation of AB is 11.78 meters. Compute the correctedhorizontal distance of AB.

A 30 m steel tape weighing 1.45 Kg is of standard length under a pull of 5 Kg,supported for full length. This tape was used in measuring a horizontal line AB whichis 735.15 m long on smooth level ground under a steady pull of 8 Kg. Assuming E = 2x 10^6 Kg/cm^2 and the unit weight of the steel is 7.9 x 10^-3 Kg/cm^3. It was laternoticed that the measurements were performed on a sloping ground (gentle slopeonly) and the difference in elevation of AB is 11.78 meters. Compute the correctedhorizontal distance of AB.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 28P

See similar textbooks

Similar questions

A horizontal force P acts on the top of the 30 N block having a width of 25 cm and a height of 50 cm. If the coefficient of friction between the block and the plane is 0.33. a. What is the value of P for motion to impend? b. Is the motion will impend due to overturning?
A 50 m tape is supported only at its ends and under a steady pull of 8.5 kg was used to measure a bridge, recorded as 1000 m. If the tape weighs 0.98 kg, determine the correct measurement of the bridge.
! use the given datas on solving ! refer image when needed. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E=2*10^ 6 kg/cm^ 2 and the unit weight y of the steel to be 7.9*10^ -3 kg/cm^ 3 . a) Determine the cross-sectional area of the tape. Hint: y = W/V b) Determine the correction due to pull for one tape length. c) Determine the total correction due to pull. d) Determine the corrected distance.
SHOW SOLUTION A steel tape with a cross-sectional area of 0.03 cm2 is 50.0 m long under a pull of 7 kg when supported throughout. It is used in measuring a line 2750.0 m long under a steady pull of 10 kg. Assuming E = 2.0 x 106 kg per cm2. Determine the correct length of the line due to tension.A) 2750.1375 m B) 2749.9975 m C) 2750.0025 m D) 2749.8625 m
Assign the values of shear force and bending moment to the image beam as a function of the x coordinate. q = 22 kN / m, F = 14 kN, M = 10 kNm L1 = 1.2 m, L2 = 1.9 m, L3 = 1.2 m, L4 = 1.9 m Use units [kN, m] Enter your answers to three decimal places. Do not round off the invoices in the intermediate stages, but only the final answer!
In every measurement, a 100-meter tape is suspended at the ends under a pull of 15 kg. It isalso supported at 30 m and 75 m marks. If the tape is used to measure a 543.25 long line,determine the total correction due to sag? The tape weighs 5 kg.
A horizontal force P acts on the top of the 30N block having a width of 25 cm and a height of 50 cm. If the coefficient of friction between the block and the plane is 0.33. What is the value of P for motion to impend?
Using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 5.6 m b = 4.4 m c = 15.9 kn/m d = 22 kn QUESTIONS: 1. Determine the VERTICAL REACTION at B in KN. 2. Determine the SLOPE at B in DEGREES. 3. Determine the DEFLECTION at D in MM. 4. Determine the DEFLECTION AT MIDSPAN OF THE BEAM in MM. Thank you! Please answer all. ❤️
A rectangular bar is subjected to tensile forces of 2230 kN. Use E = 110 GPa and ν = 0.34. Determine the change in the dimension of its cross-section along X and Z directions. Also, calculate the change in the volume of the bar.
*refer image for correct data Pls solve all questions for full answers. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E=2*10^ 6 kg/cm^ 2 and the unit weight y of the steel to be 7.9*10^ -3 kg/cm^ 3 . a) Determine the cross-sectional area of the tape. Hint: y = W/V b) Determine the correction due to pull for one tape length. c) Determine the total correction due to pull. d) Determine the corrected distance.
A tangential force of 0.004 K N affected the upper surface of a rectangle 5 mm high, 3 cm long and 5 cm wide, on its top surface. Not the shear modulus of elasticity of the body material is 3.33 * 10 N/ m Find (1) shearing stress (2) shearing strain (3) the resulting displacement in the direction of the force?
Determine the slope and vertical displacement of point A on the beam shown in the accompanying illustration. Use Conjugate Beam Method. E = 200,000 MPa