1.5×10-6 S/km. Ok.......... A 30 transmission line 200km.longhajthe following constants.0.1657/km; 7/-0.255/kmR/Q=Y/₁ = 1·5× 10² 5/kmcalculatethe sendinglineof 20 MWtheby rigorous methodend voltage whena loadlaggingisdeliveringat0.8 power factorThe receiving end voltageKept constantConstant at110 kv.

3 phase transmission line has parameters Find the sending end voltage VS sending end current IS.

@ A 30 transmission line 200 km long haj the following constants. R/0 = 0·1657/²; x/0 - 0-2534/km ٥٠/6-2 Y/₁ = 1·5 x 108 S/km calculate the sending the by rigorous method end voltage when delivering a load at line of 20 MW lagging is керт 0.8 power facto The receiving and voltage at 110 KV

@ A 30 transmission line 200 km long haj the following constants. R/0 = 0·1657/²; x/0 - 0-2534/km ٥٠/6-2 Y/₁ = 1·5 x 108 S/km calculate the sending the by rigorous method end voltage when delivering a load at line of 20 MW lagging is керт 0.8 power facto The receiving and voltage at 110 KV

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

A 3-phase, 50 Hz overhead transmission line, 100 km long, 110 kV between the lines at the receiving end has the following constants : Resistance per km per phase = 0·153 W Inductance per km per phase = 1·21 mH Capacitance per km per phase = 0·00958 µF The line supplies a load of 20,000 kW at 0·9 power factor lagging. Calculate using nominal p representation, the sending end voltage, current, power factor, regulation, and the efficiency of the line. Neglect leakage.
A 3Ø 60 hz. 15 miles long transmission line provides 10 MW @ a p.f. of 0.9 lag. at a line to line voltage of 34.5 kV. The line conductors are made of 26/7 strands 300,000 CM ACSR conductors that operates @ 25ºC and are equilaterally spaced 3 ft. apart. Calculate the following a. sending end voltage b. % voltage regulation of the line c. efficiency of the transmission line
An energy transmission line with a length of 130 km transmits 150MVA of power at 380 kV voltage. The conductors used have a conductivity of 35 [m / mm mm²] and a diameter of 28.11mm. The final temperature reached by this transmission line is 66 degrees. (NOTE = temperature coefficient of conductor a20deg = 0.00403deg ^ -1) Approximately how many kWatts is the total loss in the three-phase line at 20 degrees?
A 3-phase, 50 Hz overhead transmission line, 100 km long, 110 kV between the lines at the receiving end has the following constants :Resistance per km per phase = 0·153 ΩInductance per km per phase = 1·21 mHCapacitance per km per phase = 0·00958 μFThe line supplies a load of 20,000 kW at 0·9 power factor lagging. Calculate using nominal π representation, the sending end voltage, current, power factor, regulation and the efficiency of the line. Neglect leakage
A power of 90+j70 MVA is drawn from the end of a 220 km three-phase transmission line with a voltage of 380 kV. The following values are given for the line: z = 0.166 + j0.86 Ω/km and y = j6x10^(−6) w/km .Calculatethe sending end voltage, sending end current and efficiency for each of the following cases. 1-)Using short transmission line approximation. 2-)Using long transmission line approximation.
A 210 km long three-phase transmission line is operated on a 60 Hz network. Line Finally a 40 MVA power with 0.78 back power factor under 120 kV voltage is being shot. The conductor resistance value of the line is 0.10 Ω / km, the inductance value Since 1.30 mH / km and capacitance value is 0.001 µF / km, Medium Transmission Line establishing the equivalent circuit model; a) -Calculate the line current and voltage of the sending side. b) Calculate the power loss on the line. c) Calculate the% voltage regulation value of the line.
The length of a power transmission line is ℓ = 150 km, the unit effective resistance of the line is r = 0.06 Ω/km, x = 0.4 Ω/km and the admittance value of the line is y = j4.10-6 Siemens/km. The end-of-line voltage is 154 kV, the line-head voltage is 170∠10o kV. a) The characteristic impedance of the line b) The power drawn by the load according to the given values c) Calculate the maximum power that the line can transmit?
Characteristics of 165 kV, 150 MVA, 50 Hz 3-phase 100 km transmission linevalues are given below. r=0.103ohm/ kmx=0.525ohm/ kmy=3.3x10^-6 S/ km (a) Calculate the constants A and B for the equivalent circuit of this transmission line,(b) Load lagging power factor of 0.9 when the line is running at nominal (tag) value.if so, find the production side voltage. lesson: Power system analyses
Transmission and Distribution of Electric Power Answer the Following Question Please: Q) Three-phase transmission line, 60HZ, have: (50 MW, 0.866 lagging p.f. and 132 kv in receiving end. If the line have (Z = 100 <80 Ohm / phase and Y = 0.0012 <90 S). Calculate: Vs, Is, Vreg, and power factor in sending end. Also, find the transmission efficiency? For the following transmission models: 1- Short transmission line model. 2- Medium transmission line (pi) model. 3- Medium transmission line (T) model. 4- Long transmission line model. (Please show your answer steps)
A 3-ph, 60 Hz, 200 km long, 220 kV transmission line has per km per phase constants of resistance 0.033 Ω, inductive reactance 0.33 Ω, capacitive susceptance 3.3x10 -6 mho. The load at the receiving end of the line is 500 MW at 0.95 power factor leading and voltage has dropped to 209 kV. Using the PI model, calculate the voltage, current and power factor at the sending end. Please answer in typing format solution please only typing format Please I will like it please reply to
The shunt admittance and series impedance of a long transmission line are given with respect to length as follows: y =j3.5x10-6S/km z = (0.1 + j0.5)ohms/km The length of the transmission line is 400km. It wheels 150MW at 220kV and 0.85 pf lagging. Calculate the following: a) the A and B constants of the transmission line. b)the Cand D constants of the transmission line. c) the sending end voltage. d)the sending end current.
A single circuit, 60 Hz, three phase transmission line has the following parameters : R = 0.30 0/mile L = 2.10 milliHenry /mile C = 0.014 μFarad/mile b.) If the line is 75 miles long and delivers 40 MW at 132 kV and 80% lagging powerfactor, determine the sending end voltage, current, power, and power factor.Compute for the velocity propagation. Expected Answer: 151.27 kV, 199.61 A, 42.885 MW, 0.82 lag