A 4-pole shunt generator with wave-wound armature has 41 slots, each having 12 conductors. The armature resistance is 0.05 ohms and shunt field resistance s 200 ohms. The flux per pole is 25 mWb, if a load resistance of 10 ohms is connected across the armature terminals, calculate the voltage across the load when generator is driven at 1000 rpm

A 4-pole shunt generator with wave-wound armature has 41 slots, each having 12 conductors. The armature resistance is 0.05 ohms and shunt field resistance s 200 ohms. The flux per pole is 25 mWb, if a load resistance of 10 ohms is connected across the armature terminals, calculate the voltage across the load when generator is driven at 1000 rpm

Electrical Transformers and Rotating Machines

4th Edition

ISBN:9781305494817

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Three-phase Circuits

Section: Chapter Questions

Problem 9RQ: An alternator with a line voltage of 2400 V supplies a delta-connected load. The line current...

See similar textbooks

Similar questions

An alternator with a line voltage of 2400 V supplies a delta-connected load. The line current supplied to the load is 40 A. Assuming the load is a balanced three-phase load, what is the impedance of each phase?
A long-shunt compound-wound generator gives 240 volts at F.L. output of 100A. The resistances of various windings of the machine are : armature (including brush contact) 0.1 Q, series field 0.02 Q, inter pole field 0.025 2, shunt field (including regulating 0.2 resistance) 100 2. The iron loss at F.L. is 1000 W; windage and friction losses total 500 W. Calculate F.L. efficiency of the machine.
A six-pole lap wound armature rotating at 350 rpm is required to generate 260 V. The effective flux per pole is about 0.05 Wb. If the armature has 120 slots, determine the suitable number of conductors per slot and hence determine the actual value of flux required to generate the same voltage
Q1 / A DC shunt generator delivers 187 A at 260 V. The armature resistance and shunt field resistance are 0.028 2 and 48 2 respectively. The sum of stray losses equal 950 W. Find the machine efficiency.
A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
A shunt generator delivers 195 A at terminal p.m. of 250 V. The armature resistance and shunt field resistance are 0.02 ohm and 50 ohm respectively. The iron and friction losses equal 950 W. Find (a) E.M.F. generated (b) Cu losses (c) output of the prime mover (d) commercial, mechanical and electrical efficiencies.
A piezoelectric actuator is made from a stack of 20 square piezoelectric pads, each 10mm squarewith a thickness of 2mm? Calculate the maximum displacement when 1kV is applied given that d33=100×10-12 C/N, er = 50 and Y = 50GPa.
A 250-V, 4-pole, wave-wound d.c. series motor has 782 conductors on itsarmature. It has armature and series field resistance of 0.75 ohm. The motor takesa current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb
Q1. Long-shunt generator delivers a load current of 30 A at 220 V. It has armature and shunt field resistances of 0.050, 2000 respectively: A- calculate the generated emf, the copper loss in armature, shunt field loss and the total copper loss. B-if the iron and friction loss is 1000W. Calculate the electrical efficiency, mechanical efficiency, commertial efficiency and maximum efficiency. (Armature reaction may be neglected) Q2. A 220V, 4-pole, lap-connected, shunt motor with 800 conductors in armature slots. The armature and shunt field resistance are 0.62 and 2200 respectively. The motor runs to supply load with 8000W and draw current (50amps) from the mains. The flux per pole is 25mWb A- Calculate the gross torque developed by the armature, the shaft torque (useful), and the lost torque. B- Calculate the gross power developed by the armature, the iron and friction lost power, mechanical efficiency, electrical efficiency, and the overall efficiency. Armature reaction may be…
Two transformers rated at 100 kVA each are connected in an open-delta connection. What is the total output power that can be supplied by this bank?
An inductor has an inductance of 0.025 H and a wire resistance of 3 Ω. How long will it take the current to reach its full Ohm’s law value?
The collector leakage current in a transistor is 300 μA in CE arrangement. If now the transistor is connected in CB arrangement, what will be the leakage current? Assume β = 120. (2) For a certain transistor, IB = 20 μA; IC = 2 mA and β = 80. Calculate ICBO. (3) In a transistor, IB = 68 μA, IE = 30 mA and β = 440. Determine α rating of the transistor. Then determine the value of IC using both the α rating and β rating of the transistor.