Tout, out Water damping, 8 Tin On Crankshaft spring constant, K Flywheel + Engine inertia, J, FIGURE P2-14 The input to the propeller system is torque, Tin and the output is the prop speed, éout- The impedances are based on torque, as the flow variable and angle as potential variable. a. Construct the impedance diagram and label all signals.

Tout, out Water damping, 8 Tin On Crankshaft spring constant, K Flywheel + Engine inertia, J, FIGURE P2-14 The input to the propeller system is torque, Tin and the output is the prop speed, éout- The impedances are based on torque, as the flow variable and angle as potential variable. a. Construct the impedance diagram and label all signals.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Try to write the motion equations of the system under the following conditions, and judge whether it is acceleration, deceleration or uniform speed(The arrows in the figure show the actual direction of torque). TX-IL IN CIL IW TW TL TO TL (4) IL TV TL TH= TL (1) Judge whether the intersection in the figure below is a stable working point? "Tx. Iz K
give the a) A turbine connected to an electric generator through a gearbox can be modelled as illustrated in Figure 1 = 951 kgm² J2 = 950 kgm² equivalent inertias of the rotary system. The shafts provide a stiffness of k1 = 9.9x10¹Nm/Rad k2 = 4.9x106Nm/Rad spectively. The letters in the parameters represent digits of student numbers: A is the third digit, B is the fifth digit, D is the sixth digit, and F is the seventh digit. i) Draw free-body diagrams ii) Write the equations and put them in matrix form iii) Calculate the dynamic stiffness values iv) Find the natural frequencies and draw mode shapes of the system v) Discuss the effect of coupling stiffness k₁₂ on the natural frequencies k₁₁ 01 k12 O Figure Q2.
Q2 Figure Q2 shows the schematic diagram of wind turbine which used in power plant. By using the exact solution method, it is found that the fundamental natural frequency for the system is wn = 0.6/kt/J rad/s. Assume that J, =J2 = J, and k; = k;2 = kị. By using Rayleigh's method, predict the fundamental natural frequency in Hertz natural frequency in Hertz unit and its corresponding mode shape for Q2(a) answer if the initial trial vector is (). Use J= 2, and k, = X, and show up 2.9 %3D X=6 Rotor Hub - Low-speed shaft - Gearbox J, - High-speed shaft Nacelle- |02 Tower LGenerator J: Figure Q2 Blade Blade
pleassssse solve question 5, statics
which equation is used if the system underdamped. can you pls share the whole eqn
Dtes 6) Take a look at the picture below. Initially the system is at rest. The spring is activated and sends the mass moving with tangential speed "v" and the disk rotating with angular velocity "w". Find expressions for these parameters in terms of the variables given. Final I nitind At Rest Dişk Rolutes Sprivag: compressx a mass と szring Cons & ingetid velocty muss Rotafiond ふnertiu ofDk
1. Linearized the dynamic model of the system shown below: - cô – mgL sin 0 + u. daor at| L sine mg
1. Find: Vs, wa/c, and wa/A Use relative motion analysis OR Instantaneous center of rotation Given: 0= 58° @=39° BC=3m AB=9m V₁ = 12 m/s your choice mak 437 B
do the question by the concepts of statics and mention all the steps clearly
Suppose the four legs of Sitting on abe are Chair You identical this Scm springs. when you on Chair the chau's downwatd. what Constant of each is spring Spring? D Now Suppose that the Seae has only One leg. This leg is made by. tonnectin all the four spings in line when you sit it, the chair goes Scm downward. what is the Spring a on Constant of each spring ? (note): You owń uweight / mass for calculation' if you want to get numericlal Values Should use your as answer? Shot on vivo S1 00 AI Triple Camera
Q4) In Fig.2, The location of the tool, 77 is not accurately known. Using force control, the robot feels around with the tool tip until it inserts it into the socket (or Goal) at loca- tiongr. Once in this "calibration" configuration (in which (G) and (T) are coincident), the position of the robot, is figured out by reading the joint angle sensors and com- puting the kinematics. Assuming T and T are known, give the transform equation to compute the un- known tool frame,T. 2 Fig.2
Q2:- in fig (1) The T=4500 N.mm, m=3 kg, r=0.5m,k=10 N.mm b= 12, Kb=15, R=0.5, L=3 find the angular acceleration if the angular velocity =20 rad / sec, the current and T.F R Armature D circuit Rotor Fixed field