A 4 pole wave wound shunt generator delivers 195A at a terminal voltage of 205V. Ra and Rsh are 0.05Q and 702 respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv)

A 4 pole wave wound shunt generator delivers 195A at a terminal voltage of 205V. Ra and Rsh are 0.05Q and 702 respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.48P

See similar textbooks

Related questions

Q: A voltage waveform, e(t) = 100 V sin ( 314 rad/s t), is connected across a 5mH pure inductance. Calc...

Q: A capacitor drawing 4 kvar is placed in parallel with the electro-magnet that draws 3 kW of active p...

A: Capacitor can supply only reactive power and takes zero active power. Apparent power = active power ...

Q: 4(VD – 20) + 11VD + 6(VD -Vb) = 0 Find VD and Vb

Q: The temperature coefficient of resistivity of carbon is -0.0005/C° . If the resistor is made of grap...

A: Solve the problem

Q: A coil with 200 turns is linked with the flux given by o(t)=2tcos(6t + 34° )Wb. Determine the magnit...

A: In this question , coil is given with flux associated with it...We have to find out voltage induced ...

Q: Q1- For the circuit of Figure below: a) Determine Thevenin equivalent circuit at the output terminal...

A: We need to find out Thevenin equivalent theorem, and R value for maximum power transfer and value of...

Q: A single-phase 400 kVA transformer has an efficiency of 99.13% at half load unity power factor where...

A: It is given that: S=400 KVAη=99.13 % at half load unity power factorη=98.77 % at full load 0.8 power...

Q: The gate characteristic of an SCR has a straight-line slope of 125. What should be the gate-source r...

Q: 3-Find out any ten sensors which are been used in modern robots with its function. 4 From your view ...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: 20V ov Vin R Vout 8V -10V

Q: Find the time constant for the RC circuit in Fig.

A: To solve above question, one should understand the behavior of Inductor and capacitor in DC circuit....

Q: For the balanced positive-sequence three-phase circuit below, given that Var-100410° V and Za=15455°...

Q: Volts Calculate the output voltage Vo from the circuit shown below. Vo = D1 10 V D2 OV

Q: Compare analog and digital instrument performance.

A: Analog instruments are those that produce output that vary constantly with the amount to be measured...

Q: 2. A voltage waveform, v(t) = 200 V sin ( 250 rad/s t ), is connected across a series combination co...

Q: omplete solution and Draw the waveform of the given clamper circuit. Determine: 1. At +20V, what i...

A: At Vin=20VVo=? At Vin=20V diode is in forward bias and becoming short-circuit. Vo=-8V2)20=Vc-8Vc=2...

Q: For the general properties of a system i.e causality, linearity, and stability. Determine which prop...

A: GIVEN: (1) yn=n x n(2) Y(t)= x2(t) FIND: the given equation hold which of the following...

Q: 10.41 Suppose E(y,t) = Eo1 cos(wt – By)a, + E,2 cos(wt – By + 4)a, V/m. Determine the polarization w...

A: It is given that: Ey,t=Eo1cosωt-βyax+Eo2cosωt-βy+ϕaz V/m

Q: Two equal-valued resistors dissipate a power of 10 W. The resistors are connected in:

A: Given information: Two resistors, having equal values, dissipate a power of 10 W. The type of connec...

Q: A tor the creuit Shown beluo where all resislors are given in k2, apply Transformation technique to ...

Q: A coil with resistance of 100 and an inductance of 15 mH is connected in series to the paralle combi...

A: Solve the problem

Q: 8085 microprocessor, the ISR for handling trap interrupt is at which location?

A: In this question we will write about the ISR for handling trap interrupt is at which location in 808...

Q: (b) For the following set of voltages, Va= 208sin(@t + 27°) V= 208sin(@t + 147°) V. = 208sin(@t – 93...

A: Phasor is a vector with phase Use this to analyse the given phasors As the phase continuously change...

Q: A thyristor (SCR) structure is a a. N-P-N-P device b. N-P-N device c. P-N-P ...

A: SCR stand for silicon controlled rectifier. It is a device that controls current in only one way. I...

Q: T QF D Q A B CLK

A: Given the circuit, as shown below: We need to construct the complete state diagram for the Finite S...

Q: (c) Two (2) ideal voltage sources, V1 and V2 are connected together by a line impedance, Z. (i) Draw...

A: C)(I) To draw the circuit Ii)to find the Real and reactive power supplied by each source iii) Dete...

Q: 15. a. Find the Thévenin equivalent circuit for the portions of the network of Fig. 9.139 O external...

A: Brief description : In case of electrical circuits any complex circuit can be reduced into simplifie...

Q: Please answer the following: a) What is the resistance in the circuit? b) What is the reading in m...

A: In this question potentiometer is given....We have to find out it's total resistance and current flo...

Q: A compound DC motor with lap-wound armature is connected to a 132V source. Shunt field resistance is...

A: Note : It is not given long shunt OR short shunt so considering long shunt and drawing the equivalen...

Q: Draw rough sketches showing the following: a. A current which lags the voltage by 60 degrees b. A cu...

A: Given a. A current which lags the voltage by 60 degreesb. A current which leads the voltage by 60 d...

Q: 10 1F 1Q i1(t) IF 12(t) 2H

Q: (c) A 230 V, 50 Hz power source is connected to the some loads, the source is supply current with po...

Q: In the figure shown, the voltage at Vxy is equal to

Q: Calculate the inductance (H) of an air cored coil that has a length of 9 cm, a core with rectangular...

A: Consider the formula for the inductance of the air cored coil is, L=μN2Al Here, N is the number of t...

Q: (a) Find the content of R20 after each of the following instruction is executed. Show your working s...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: 2. A 4600 to 230 Volts, 60 Hz step down transformer has a core dimension of 3.00 by 4.40 inches. A m...

Q: The impedance of the primary windings of a single-phase transformer with a transformation ratio of 6...

Q: 2. Obtain the transfer function H(s) = 1(8)/L(6) IH ell 1F

A: Since you have posted the multiple questions so we are supposed to answer the 1st one only.

Q: A 25 hp 240 V shunt motor draws 88.5 A when delivering rated load. The armature resistance of the mo...

A: The solution is given below

Q: (c) A balanced Y-connected load with a phase resistance of 12 Q series with reactance of 15 2 is sup...

Q: For sensor current sinking circuit, the load is connected a. to ground b. to supply voltage c. f...

A: Consider the current sinking device is used in conjunction to the micro-controller systems.

Q: 17. For the self-bias configuration of Fig. 6.81, determine: (a) Ipo and VGsg (b) VDs and Vp. * 18. ...

Q: Q3 Instrument transformers are designed to transform voltage or current from the high values in the ...

A: Difference Between current and potential transformer

Q: What is the power transmitted by the isotropic radiator having a field intensity of 1.51 V/m at 6om?...

A: Note : After calculating the power transmitted by the isotropic radiator we come to know that none o...

Q: The transfer function of a linear system is 2s H(s) s+6 Find the output y(t) due to the input 5e¯"u(...

Q: Fill in the bianks / Tdentim volts Given the circuit below, calculate the voltage drop across R1 whe...

Q: Find v(t) and i(t) in the circuit shown. i 4Ω + v,= 20 sin(10t + 30°) V 0.2 H - (+ I

Q: 50 hz. current of 2 A flows in a circuit consisting of an adjustable resistor and a 56.6 uF capacito...

Q: An SSB system requires 100 W transmitted power for reliable transmission. How much power is needed i...

Q: A 24-V battery is used to supply a 3-carbon type resistor network and two lamps. The connection of t...

A: This question belongs to network theory . It is based on the calculation of total resistance and tot...

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

A 4 pole wave wound shunt generator
delivers 195A at a terminal voltage of
205V. Ra and Rsh are 0.050 and 702
respectively. Neglecting brush drop,
determine (i) armature current (ii) current per
parallel path (i) generated voltage and (iv)
Power developed.
armature current
current per parallel path
generated voltage
Power developed

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shunt generator supplies a 31kW load at 230V through cables of resistance, R = 122mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =51mΩ. Determine the following below: The terminal voltage is, Answer and unit for part 1 The e.m.f. generated in the armature is,
a) 3-phase star-connected synchronous generator supplies a current of 10A having phase angle of 20° lagging 400V (phase voltage). Given the direct and quadrature axis reactances as 10ohms and 6.5ohms respectively and neglecting armature resistance, Find: 1. The load angle 2 The direct and quadrature components of armature currents 3. Voltage regulation
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
4. A 6 pole wave wound shunt generator delivers 200A at a terminal voltage of 240V. Ra and Rsh are 0.03Ω and 70Ω respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv) Power developed. armature current ? current per parallel path ? generated voltage ? Power developed ?
A 60 MVA, 69.3kV, three-phase synchronous generator has a synchronous reactance of 15 ohms/phase and negligible armature resistance. The generator is delivering rated power at 0.8 power factor lagging at the rated terminal voltage to an infinite bus bar. What is the maximum three-phase power that can be generator can deliver before losing its synchronism?
A long-shunt compound generator delivers a load current of 50A at 500V and has armature, series field and shunt field resistances of 0.05 ohms, 0.03 ohms and 250 ohms respectively. Calculate the generated voltage and the armature current. Allow 1V per brush for contact drop.
A three-phase, 100-MVA, 20-kV generator is connected to a three-phase, 100-MVA, 20-kV motor through a transmission line. The reactances of the generator and motor are 0.25 and 0.20 per unit, respectively. The line reactance is 0.10 per unit. The motor is taking 50 [MW] at 0.8 power factor leading at rated voltage. Suppose a three-phase short circuit occurs at the generator terminals, determine the transient currents in the generator and motor as well as the short-circuit current.
A 230VAC rated, 60 Hz, 10-Hp Single-phase AC motor is to be connected for across-the-line starting. Determine its conductor size if the ambient temp and RHW copper-clad aluminum will be used.
A short shunt compound generator has an armature, shunt field and series fieldresistances of 0.02 ohm, 80 ohm and 0.03 ohm respectively. The generator’s induced emfis 510V when the terminal voltage is 500V. How much load current is delivered underthis condition? Answer: 197.47A
Two generators rated 200MW and 400MW are operating in parallel. The droop characteristics of both the governor have a drop of 4%. from no load to full load. Assuming that the generators are operating at 50Hz at no load, how would a load of 600MW be shared between them? What will be the system frequency at this load? Assume free governor operation.
a) With the aid of a diagram and phasor diagram, explain the double-reactance concept for salient-pole alternators. b) 3-phase star-connected synchronous generator supplies a current of 10A having phase angle of 20° lagging 400V (phase voltage). Given the direct and quadrature axis reactances as 10ohms and 6.5ohms respectively and neglecting armature resistance, Find: 1. The load angle 2 The direct and quadrature components of armature currents 3. Voltage regulation
A 3 phase, star connected synchronous generator supplies current of 10A having phase angle of 20º lagging at 400V. Find the load angle and the components of armature current Id and Iq if Xd = 10 ohm and Xq = 6.5 ohm Assume armature resistances to be negligible