A 40-mm-diameter solid shaft is subjected to an axial force of P = 2480 N, a vertical force of V = 1880N, and a concentrated torque of T= 66 N-m, acting in the directions shown. Assume L = 130 mm. Determine the normal stress oy at point H. H. K O 29.3 MPa O 44.7 MPa O 40.9 MPa О 34.7 МРа O 55.9 MPa eTextbook and Media

A 40-mm-diameter solid shaft is subjected to an axial force of P = 2480 N, a vertical force of V = 1880N, and a concentrated torque of T= 66 N-m, acting in the directions shown. Assume L = 130 mm. Determine the normal stress oy at point H. H. K O 29.3 MPa O 44.7 MPa O 40.9 MPa О 34.7 МРа O 55.9 MPa eTextbook and Media

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth. a. 17.8 b.393.9 c.63.0 d.3.9
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
A propped cantilever beam of length ? = 1 m, with an inner hinge at point B, carries a uniformly distributed load ?, as shown in Figure Q1 (a). The beam is made from a circular hollow section with an inner radius of ?? = 5 cm and a thickness of ? = 2 cm (refer to Figure Q1 (b)). The maximum allowable longitudinal stress of the beam is 150 N/mm2.
if the beam is subjected to a bending moment of m = 10 kN•m, determine the bending stress in the beam at points a and b, and sketch the results on a differential element at each of these points.
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in
b) An electric pole is held vertically by three equally spaced wires tied at the top of the pole. Each wire is inclined at 45⁰ with a tension of 1 kN, Calculate the vertical stress increase at 1 m depth and the elastic settlement below the axis if E is given as 40 MPa and μ = 0.45. Use Boussinesq’s point load theory
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
I want Normal stress developed in segment AB. A homogeneous bar with a cross-sectional area of 400 mm2 is attached to fixed supports as shown inthe figure. It is subjected to lateral forces P1 = 20 kN and P2 = 50 kN. Determine the normal stressdeveloped in segments AB and BC. Answer: σAB = 80.55 MPa
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG