A 45 kg box is at rest at one end of a 2 meter board. That end of the board is slowly raised at an incline until the box starts to slide. At that point, the angle is at 34 degrees. The coefficient of kinetic friction is 0.50N. Please help me calculate the coefficient of static friction between both the box and the board?

A 45 kg box is at rest at one end of a 2 meter board. That end of the board is slowly raised at an incline until the box starts to slide. At that point, the angle is at 34 degrees. The coefficient of kinetic friction is 0.50N. Please help me calculate the coefficient of static friction between both the box and the board?

Name: A 45 kg box is at rest at one end of a 2 meter board. That end of the
Uploaded: 2024-03-20T06:57:57.000Z
Channel: Bartleby
Description: A 45 kg box is at rest at one end of a 2 meter board. That end of the board is slowly raised at an incline until the box starts to slide. At that point, the angle is at 34 degrees. The coefficient of kinetic friction is 0.50N. Please help me calculat

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter5: Newton's Laws Of Motion

Section: Chapter Questions

Problem 76PQ: Jamal and Dayo are lifting a large chest, weighing 207 lb, by using the two rope handles attached to...

See similar textbooks

Similar questions

Jamal and Dayo are lifting a large chest, weighing 207 lb, by using the two rope handles attached to either side. As they lift and hold it up so that it is motionless, each handle makes a different angle with respect to the vertical side of the chest (Fig. P5.76). If the angle between Jamals handle and the vertical side is 25.0 and the angle between Dayos handle and the vertical side of the chest is 30.0, what are the tensions in each handle? FIGURE P5.76
A 4.00 kg block rests on a 30 degree incline. If the coefficient of the static friction between the block and the incline is 0.700, what magnitude of horizontal force F must act on the block to start it moving up the incline?
A 4.0 kg block is on the verge of sliding down an inclined plane with a θ-degree angle of incline. If the coefficient of static friction is 0.7536, what is largest possible value of the angle θ?
The static friction coefficient between the block and the inclined surface is 0.2. What is the minimum force that should be applied to the block perpendicular the surface in order to prevent the block from sliding down?
A block of mass 4.20 kg is pushed up against a wall by a force P that makes an angle of θ = 50.0°angle with the horizontal as shown below. The coefficient of static friction between the block and the wall is 0.270.
What is the magnitude of the static friction force required to keep a 2.00 kg block resting on an inclined plane at an angle 25 degrees? If the angle was increased, such that the incline plane was steeper, would the magnitude of the static friction force required to hold the block at rest increase, decrease, or stay the same?
Land Rover ads used to claim that their vehicles could climb a slope of 45°. For this to be possible, what must be the minimum coefficient of static friction between the vehicle’s tires and the road?A. 0.5 B. 0.7 C. 0.9 D. 1.0
A dockworker adjusts rope which keeps a ship from drifting alongside a wharf. If he exerts a pull of 200 N on the rope, which has turns of 1 ¼ around the mooring bit, what force T can he support? The coefficient of friction between the rope and the cast-steel mooring bit is 0.30
A block weighing mA = 10 kg is placed on a plane with slope angle 30.0 degrees and is connected to a hanging weight of mass mB by a cord passing over a small frictionless pulley as shown in the picture. The coefficient of static friction is 0.42, and the coefficient of kinetic friction is 0.30. If the two blocks are moving, what is the force of friction?
A 250 N block is initially at rest on a flat surface that is inclined at 30°. if the coefficient of the static friction is 0.30, find the force required to start the block moving up the plane.
In the figure, block M2 is sitting on a table and is connected by mass-less chords to block M1 and to a vertical wall. The coefficient of static friction between M2 and the table is Us=0.60. Block M1 has a mass of 8 kg. The angle made by the chord and the wall is 55 degrees. What minimum mass must block M2 have in order to remain stationary and not slide?
A tool box of weighing 50.0 N rests on a horizontal surface. The coefficient of static friction between the box and the surface is 0.40, and the coefficient of kinetic friction is 0.20. If no horizontal force is applied to the box and the box is at rest, how large is the friction force exerted on the box?