A 50.0 g mass is placed at the 20 cm mark in meterstick as shown in the figure. what is the mass of the meter stick if fulcrum is placed at the 39.5 cm mark and the meter stick remains horizontal in static equilibrium? 60 80 100 20 39.5 50 g 18.0 g B) 93.0 g 45.0 g D) 120.0 g E 135.0 g

A 50.0 g mass is placed at the 20 cm mark in meterstick as shown in the figure. what is the mass of the meter stick if fulcrum is placed at the 39.5 cm mark and the meter stick remains horizontal in static equilibrium? 60 80 100 20 39.5 50 g 18.0 g B) 93.0 g 45.0 g D) 120.0 g E 135.0 g

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotation Of A Rigid Object About A Fixed Axis

Section: Chapter Questions

Problem 10.16CQ: A person balances a meterstick in a horizontal position on the extended index fingers of her right...

See similar textbooks

Similar questions

An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A person balances a meterstick in a horizontal position on the extended index fingers of her right and left hands. She slowly brings the two fingers together. The stick remains balanced, and the two fingers always meet at the 50-cm mark regardless of their original positions. (Try it!) Explain why that occurs.
In analyzing the equilibrium of a flat, rigid object, you are about to choose an axis about which you will calculate torques. Which of the following describes the choice you should make? (a) The axis should pass through the objects center of mass. (b) The axis should pass through one end of the object. (c) The axis should be either the x axis or the y axis. (d) The axis should pass through any point within the object. (e) Any axis within or outside the object can be chosen.
An object is acted on by a single nonzero force of magnitude F. (a) Is it possible for the object to have zero acceleration a? (b) Is it possible for the object to have zero angular acceleration ? (c) Is it possible for the object to be in mechanical equilibrium?
The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22
Two window washers. Bob and Joe, are on a 3.00-m-long, 345-N scaffold supported by two cables attached to its ends. Bob weighs 750 N and stands 1.00 m from the left end, as shown in Figure P8.82. Two meters from the left end is the 500-N washing equipment. Joe is 0.500 m from the right end and weighs 1 000 N. Given that the scaffold is in rotational and translational equilibrium, what are the forces on each cable? Figure P8.82
A worker applies a torque to a nut with a wrench 0.500 m long. Because of the cramped space, she must exert a force upward at an angle of 60.0 with respect to a line from the nut through the end of the wrench. If the force she exerts has magnitude 80.0 N, what magnitude torque does she apply to the nut?
(a) Give an example in which the net force acting on an object is zero, yet the net torque is nonzero, (b) Give an example in which the net torque acting on an object is zero, yet the net force is nonzero.
Figure CQ10.15 shows a side view of a childs tricycle with rubber tires on a horizontal concrete sidewalk. If a string were attached to the upper pedal on the far side and pulled forward horizontally, the tricycle would start to roll forward. (a) Instead, assume a siring is attached to the lower pedal on the near side and pulled forward horizontally as shown by A. Will the tricycle start to roll? If so, which way? Answer the same questions if (b) the string is pulled forward and upward as shown by B, (c) if the string is pulled straight down as shown by C, and (d) if the string is pulled forward and downward as shown by D. (e) What If? Suppose the string is instead attached to the rim of the front wheel and pulled upward and backward as shown by E. Which way does the tricycle roll? (f) Explain a pattern of reasoning, based on the figure, that makes it easy to answer questions such as these. What physical quantity must you evaluate? Figure CQ10.15
An automobile engine can produce 200Nm of torque. Calculate the angular acceleration produced if 95.0 of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0-kg disk that has a 0.180-m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
A simple pendulum consists of a small object of mass 3.0 kg hanging at the end of a 2.0-m-long light string that is connected to a pivot point. (a) Calculate the magnitude of the torque (due to the force of gravity) about this pivot point when the string makes a 5.0 angle with the vertical. (b) Does the torque increase or decrease as the angle increases? Explain. Figure P8.6
Two window washers. Bob and Joe, are on a 3.00-m-long, 345-N scaffold supported by two cables attached to its ends. Bob weighs 750 N and stands 1.00 m from the left end, as shown in Figure P8.82. Two meters from the left end is the 500-N washing equipment. Joe is 0.500 m from the right end and weighs 1 000 N. Given that the scaffold is in rotational and translational equilibrium, what are the forces on each cable? Figure P8.82