INSTRUCTIONS:• Please write clearly and understandable way.Write all the corresponding GIVEN with their corresponding symbols and units.• List all the MISSING/REQUIRED, and list all the FORMULA that will be used.DRAW/ILLUSTRATE THE DIAGRAM/CIRCUIT OR DRAWINGS that is related to theproblem, IF POSSIBLE, which is HIGHLY REQUIRED.•• The CONVERSION calculations with their corresponding symbols and units isrequired.• The problem's SOLUTION must be solved in a step-by-step, no shortcut, again, withtheir corresponding symbols and units.• BOXED the Final Answer.PROBLEM:A 500kg container van is being lowered into the ground when the wire rope supporting itsuddenly breaks. The distance from which the container was picked up is 3m. Find thevelocity just prior to the impact in m/s assuming the kinetic energy equals the potentialenergy.a) 5. 672b) 6.672c) 7.672d) 8.672

Answered: Image /qna-images/answer/abf962a2-a013-46fc-830d-db055dcaeccb.jpg

A 500kg container van is being lowered into the ground when the wire rope supporting it suddenly breaks. The distance from which the container was picked up is 3m. Find the velocity just prior to the impact in m/s assuming the kinetic energy equals the potential energy. a) 5. 672 b) 6.672 c) 7.672 d) 8.672

A 500kg container van is being lowered into the ground when the wire rope supporting it suddenly breaks. The distance from which the container was picked up is 3m. Find the velocity just prior to the impact in m/s assuming the kinetic energy equals the potential energy. a) 5. 672 b) 6.672 c) 7.672 d) 8.672

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The topic of CNC programming, including the comprehensive coverage of G codes and M codes, is thoroughly addressed.
There is extensive discussion on CNC programming, as well as G codes and M codes.
I neeeeeed a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala
I need only MATLAB coding please.....
Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors
Four machines used to produce a family of parts are to be arranged into a GT cell.The from-to data for the parts processed by the machines are shown in the table below.(a) Determine the most logical sequence of machines for this data. (b) Construct the network diagram for the data, showing where and how many parts enter and exit the system.(c) Compute the percentages of in-sequence moves, bypassing moves, and backtrackingmoves in the solution. (d) Develop a feasible layout plan for the cell
Please show all step, not Ai generated.
The title of our study is "Design and Fabrication of an Agricultural Spraying Attachment for an Autonomous Rover" we need help in the machine design part of our study, specifically Pump selection, battery selection, and center of gravity computation I already sent you the image of the rover Rover weight capacity 35 kilo grams (payload) Rover measurements: Wheel distance - 14.5 inches and 8.5 inches Rover platform size (width & length) 14.4 inches x 10.4 inches Height- 15.8 inches. Water tank selection More or less 25 liters *For tank selection we need to justify the size with the center of gravity, proving that is the maximum dimension or liters of the tank because the center of gravity will be higher making the rover prone to toppling Pump selection *Our sprayer design has two nozzles which splits using a tee splitter, we need to find the size of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayer has a 12V pump and a pressure from 0.2 to 0.45 mpa…
Document three phases of writing a CNC program in the form of a block diagram. Don’t need to write the actual CNC program.
Automated industrial system can increase the quality and flexibility of process.(i) Sketch an automated industrial system and briefly describe the elements of the automated industrial system.(ii) With the aids of the sketched automated industrial system in Q1(a)(i), illustrate and label the appropriate components for all the elements in an automated metal and plastic objects sorting process with conveyor system.
Please briefly explain the working principle of an Optical Encoder. Please use the sketch to help your explanation. Explanation.
I need to find the command and plot on Matlab.