CB Page viewA Read aloudAdd textV DrawHighlightA 550 rpm shaft fitted with a 35 inches diameter pulley weighing 300 lbs. This pulley delivers 40 Hp to aload. The shaft is also fitted with a 26 inches pitch diameter gear weighing 220 lb. This gear delivers 30Hp to a load. Assume that the tension of the tight side of the belt is twice that on the slack side of thebelt, determine the concentrated loads produced on the shaft by the gear in Ibs.Select one:a. 753.85b. 462.61C. 484.44***d. 264.44

Answered: Image /qna-images/answer/a3fe7d79-f4b0-454a-98cf-c36f832fbbd5.jpg

A 550 load. The shaft is also fitted with a 26 inches pitch diameter gear weighing 220 lb. This gear delivers 30 rpm shaft fitted with a 35 inches diameter pulley weighing 300 lbs. This pulley delivers 40 Hp to a. Hp to a load. Assume that the tension of the tight side of the belt is twice that on the slack side of the belt, determine the concentrated loads produced on the shaft by the gear in Ibs. Select one: a. 753.85 b. 462.61 C. 484.44*** d 264 AA.

A 550 load. The shaft is also fitted with a 26 inches pitch diameter gear weighing 220 lb. This gear delivers 30 rpm shaft fitted with a 35 inches diameter pulley weighing 300 lbs. This pulley delivers 40 Hp to a. Hp to a load. Assume that the tension of the tight side of the belt is twice that on the slack side of the belt, determine the concentrated loads produced on the shaft by the gear in Ibs. Select one: a. 753.85 b. 462.61 C. 484.44*** d 264 AA.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A roller chain is to transmit 5 hp from a gearmotor to a wood-working machine, with moderate shock. The 1-in output shaft of the gearmotor turns n = 500 rpm. The 1 ¼-in. driven shaft turns 250 rpm; C »16 in. (a) Determine the size of sprockets and pitch ofchain that may be used. If a catalog is available, be sure maximum bore of sprocket is enough to fit the shafts. (b) Compute the center distance and length of chain. (c) What method should be used to supply oil to the chain?
Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm long. Oneis solid but the other is hollow with an inside diameter of 40 mm. Both are made from steel. Compare the torsionalshear stress, the angle of twist, and the mass of the two designs if they are subjected to a torque of 850 N ·m.
A 10" in diameter helical gear carries a torque of 3,000 in-lb. It has 20 deg. Involute stub teeth and a helix angle of 30 deg. Determine: (a) the tangential component of the load on the teeth in the plane of rotation; (b) the separating component of the load on the teeth; (c) the angle of obliquity in th plane normal to the pitch element of the tooth, and (d) the resultant load on the tooth
The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a steel gear wheel that is shrunk onto the hollow shaft has an outer radius of 150 mm. The maximum allowable tangential stress developed by shrinking the gear wheel onto the hollow shaft is 200 MPa. The length of hub parallel to the shaft axis is 200 mm, and the coefficient of static friction between the hub and the shaft is 0.40. Determine the maximum torque that may be transmitted by the gear wheel without slipping on the shaft.
The input shaft to a gearbox, shown in Figure 3, operates at a speed of n1 and transmits a power of 30 hp. The output power is 27 hp at a speed of n2. (a) What is the torque of each shaft (in kip · in.) and (b) the efficiency of the gearbox? Use n1 = 1800 rpm, n2 = 425 rpm. (c) Also compute for the torsional stress on the 1.5” diameter solid shaft C, and on the hollow shaft at E whose D =2” and d = 1.5”.
A 1.5 in diameter 10-spline shaft and permanent fit has a compressive force of 2000 lbs. Find the torque applied if hub length 2 in.
What weight (kg) can be lifted by a double threaded screw that has an efficiency of 85% if it is opetated by a 52 lb force at the end of a 25 inches lever ?The pitch of the screw is 0.55 inches
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
ANSWER ASAP The worm gear rotating at 1250 rpm drives a worm wheel and whose velocity ratio is 12 to 1. A driving motor with 12 hp is used to supply the worm with worm pitch gear diameter of 3.5 in. Find the tangential force on the gear.
Write legibly, provide manual step by step solution, and diagram for below given problem. A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34in. bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 7.3ksi? Ans. 39,034.94 ft-lb
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
The shaft shown in the ﬁgure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F1 = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf·in is being transmitted through the shaft between the points of application of the forces.