A 58 F capacitor and a 471 resistor are connected to a battery of voltage 7 V as shown in the circuit. After closing the switch, when the capacitor voltage is half of battery voltage how much energy is stored in the capacitor? Express your answer in Joules (J) E 非 R C

A 58 F capacitor and a 471 resistor are connected to a battery of voltage 7 V as shown in the circuit. After closing the switch, when the capacitor voltage is half of battery voltage how much energy is stored in the capacitor? Express your answer in Joules (J) E 非 R C

Physics for Scientists and Engineers

10th Edition

ISBN:9781337553278

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter26: Current And Resistance

Section: Chapter Questions

Problem 46AP

See similar textbooks

Similar questions

Show that for V less than zero, InetI0.
A close analogy exists between the flow of energy by heat because of a temperature difference (see Section 19.6) and the flow of electric charge because of a potential difference. In a metal, energy dQ and electrical charge dq are both transported by free electrons. Consequently, a good electrical conductor is usually a good thermal conductor as well. Consider a thin conducting slab of thickness dx, area A, and electrical conductivity , with a potential difference dV between opposite faces. (a) Show that the current I = dq/dt is given by the equation on the left: ChargeconductionThermalconductiondqdt=A|dVdx|dQdt=kA|dTdx| In the analogous thermal conduction equation on the right (Eq. 19.17), the rate dQ/dt of energy flow by heat (in SI units of joules per second) is due to a temperature gradient dT/dx in a material of thermal conductivity k. (b) State analogous rules relating the direction of the electric current to the change in potential and relating the direction of energy flow to the change in temperature.
A copper wire of 3.2 mm in diameter and 4 m length carries a certain amount of current. The conductionelectron density in copper is 8.49x1028 electrons/m3. A 75.0-Ω resistor is connected with the copper wireto the terminals of a battery whose emf is 11.0 V and whose internal resistance is 0.8 Ω. Calculate (a) thecurrent in the circuit, (b) the current density in the wire, (c) the terminal voltage of the battery, Vab, and (d)the power dissipated in the resistor R, (e) the power dissipated in the battery’s internal resistance r, (f) the resistivity of the wire, (g) the drift velocity of the free electrons, and (h) Estimate the rms speed ofelectrons assuming they behave like an ideal gas at 20°C. Assume that one electron per Cu atom is free tomove (the others remain bound to the atom).
21) A)he pn junction capacitance C is A) proportional to the charge space width B) not depend on the charge space region C) inversely proportional to the charge space width D)none of thesedo B)At room temperature a semiconductor material is A) Conductor B) Slightly conducting C) Perfect conductorco D)Perfect insulator
Find the equivalent resistance of the network in the circuit and the current in eachresistor. The source of emf has negligible internal resistance. R1= 4 Ω, R2= 6 Ω, and R3= 3 Ω. Round off in nearest hundredths.1. RT = ________2. IT = ________ 3. I1 = ________ 4. I2 = ________ 5. I3 = ________ 6. V1 = ________7. V2 = ________ 8. V3 = ________
A photoresistor is used in a voltage divider as R2. V = 9.0 V and R1 = 500 Ω. a) What is the output voltage, V2, across R2, when a bright light strikes the photoresistor and R2 = 475 Ω? b) When the light is dim, R2 = 4.0 kΩ. What is V2? c) When the photoresistor is in total darkness, R2 = 0.40 MΩ (0.40 x 106 Ω). What is V2?
Two 3.8microF capacitors, two 2.2kohms resistors and a 16.0V source are connected in series. Starting from the uncharged state, how long does it take for the current to drop from its initial value to 1.50 mA
The following graph represents the charge-discharge profile of a Li-ion battery in the 1st and 50th cycles, cycled at a rate of 0.1 C (1C = 274 mA h g-1 ) in the voltage range of 3.0 to 4.6 V. The battery is made up of LiCoO2 cathode and Li anode. Answer the following questions. a. What is the value of charge-discharge current density in this case? How long does it take for this battery to discharge from 4.6 V to 3.0 V in 50th cycle? b. Calculate Coulombic efficiency at 1st and 50th cycles. Why are these values different? c. How would this graph look like if LiCoO2 and Li were replaced by MnO2 and graphite electrodes respectively Make a rough sketch. d. Mention any two practical disadvantages of this battery?
If the network capacitors is connected to a 36 V source and the capacitance of C1 and C2 = 4.0 F and C3 and C4 = 6.0 F, what is the equivalent capacitance and the total charge ?
When a charge Q moves through a potential difference V, the value QV gives the energy transferred. (coulombs x joules/coulomb = joules) Dividing by the time t, we obtain a measure of power. (QV/t = IV, since Q/t = I.) Thus the rate of energy change in a resistor can be expressed as power P, and for our resistors, P = IV. This power is in the form of heat. If the power is too great, the resistor may fail. Where the resistor is 330 Ω, calculate the power produced as heat at the point of maximum voltage applied.
An engineer is designing a process for a new transistor. She uses a vacuum chamber to bombard a thin layer of silicon with ions of phosphorus, each of mass mP = 5.18 × 10-26 kg. The phosphorus ions are doubly ionized, with each phosphorus ion lacking two electrons. The ions start at rest at one end of the vacuum chamber and are accelerated by an electric field over a distance of re = 53 cm before they strike the silicon layer with velocity vP = 170 m/s. re = 53 cmvP = 170 m/s Part (a) Enter an expression for the potential difference ΔV, in volts, between the initial and final points across the vacuum chamber. ΔV = Part (b) Calculate the average electric field strength E, in volts per meters, across the vacuum chamber. E = Part (c) Calculate the average electric force F, in newtons, that the electric field exerts on each phosphorus ions. F =
A Nichrome heater dissipates 507 W when the applied potential difference is 110 V and the wire temperature is 800oC. What would be the dissipation rate if the wire temperature were held at 232oC by immersing the wire in a bath of cooling oil? The applied potential difference remains the same, and α for Nichrome at 800oC is 4.0 × 10-4 K-1.