A 6-pole, lap-wound, DC generator has a useful flux per pole of 0.08 Wb. The armature winding consists of 200 turns and the resistance is 0.055 ohms. Calculate the terminal voltage if the resistance of shunt and series field are 100 ohms and 0.02 ohms respectively; when the generator is running at 1000 rpm with armature current of 50A. Also, calculate the power output in kW for the generator. a. Assume generator connection as shunt (Rse = 0) b. Assume generator connection as short-shunt c. Assume generator connection as long-shunt

A 6-pole, lap-wound, DC generator has a useful flux per pole of 0.08 Wb. The armature winding consists of 200 turns and the resistance is 0.055 ohms. Calculate the terminal voltage if the resistance of shunt and series field are 100 ohms and 0.02 ohms respectively; when the generator is running at 1000 rpm with armature current of 50A. Also, calculate the power output in kW for the generator. a. Assume generator connection as shunt (Rse = 0) b. Assume generator connection as short-shunt c. Assume generator connection as long-shunt

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

A long-shunt, four pole, 1500-W, 250-V, duplex wave-wound DC compound generator with the rated speed of 500 r.p.m., has a shunt field resistance of 100 Ω, a series field resistance of 0.05 Ω and an armature resistance of 0.2 Ω. If the flux per pole is 48.798 mWb and a total of 620 conductors, calculate the following: (a) the generated voltage, (b) the field currents, (c) the power generated in the armature.
The armature of a 6-pole separately excited dc generator is triplex wave wound with 534 conductors. This machine delivers power to the load at 200Vwhile being driven at 900 rpm. At this load, the armature circuit dissipates 640W. If the flux per pole of this generator is 180- mWb, determine the kW rating of the load served. Assume a total brush contact drop of 2 V.
A 150 kW, 250-volt compound DC generator has its field windings which are connected in long shunt. If the shunt-field winding resistance is 20 ohms, what is the current in the series-field winding? (Note that the series field resistance is connected in series with the armature.)
The armature of a 6-pole separately excited dc generator is triplex wave wound with 534 conductors. This machine delivers power to the load at 200V while being driven at 900rpm. At this load, the armature circuit dissipates 640W. If the flux of this generator is 180-mWb, determine the kW rating of the load served. Assume a total brush drop of 2V.
A DC shunt generator has a full load output of 10kW at a terminal voltage of 240V. The armature and the shunt field winding resistances are 0.6 and 160 ohms respectively. The sum of the mechanical and core-losses is 500W. calculate the power required in kW at the driving shaft at full-load, and the corresponding efficiency and voltage regulation
A 6-pole, lap-wound, DC generator has a useful flux per pole of 0.08 Wb. The armature winding consists of 200 turns and the resistance is 0.055 ohms. Calculate the terminal voltage if the resistance of shunt and series field are 100 ohms and 0.02 ohms respectively, when the generator is running at 1000 rpa. Assume generator connection as short-shuntb. Assume generator connection as long-shunt
A short shunt compound DC generator supplies a load current of 10A at a voltage of 10 volts. If the resistance of armature, shunt field and series field windings are 0.001 ohm, 1 ohm 0.00 ohm respectively. a) Draw the the figure. And find the generated voltage.
A 4 pole ,d.c. shunt generator with a shunt field resistance of 50 ohm ,and armature resistance of 1 ohm ,has 400 lap connected conductors in its armature .the flux per pole is 20 mWb, calculate the power absorbed by a load of 10 ohm connected across the armature terminals ,when the generator is driven at 900 r.p.m.
A 6 pole, wave wound DC shunt generator has a useful total flux of 420 mWb. The armature winding consists of 220 turns each of 0.004 Q resistance, when running at 900 RPM the armature current is 50 A. If the armature winding reconnected as lap calculate the terminal voltage in case of wave and lap given that the field circuit and the speed kept same.
The output of a shunt generator is 66 A at 100 volts. Armature and field resistances are, respectively, 0.04 ohm and 25 ohms. If the efficiency at this load is 88%, determine the core and friction losses
The terminal voltage of a 75-kW shunt generator is 600 V at rated load. The resistance of the shunt-field circuit is 150 Q, and the armature-circuit resistance is 0.1 Ω. Find the generated emf. a) 612.9 V b) 621.9 V c) 692.1 V d) none of the above In a 50-kW 245-V shunt generator, 258 V are generated in the armature when the generator delivers rated load at rated voltage. The shunt-field current is 4 A. Find the resistance of the armature. a) 0.03 Ω b) 0.062 Ω c) 0.106 Ω d) none of the above A load that has a resistance of 8 Ω is connected to a separately excited generator that has an armature-circuit resistance of 0.5 Ω. A) What is the armature current when the generated emf is 130 V? a) 1.53 A b) 15.3 A c) 153 A d) none of the above
A separately excited DC shunt generator produces a no-load voltage of 150 Vdc at 1200 RPM. If the armature resistance is 3 Ohms, calculate the output voltage under the following conditions: (Note all calculations for each problem are to be performed from the base values given above). a) The speed is reduced to 875 RPM. Vout = __________________ b) The field current is increased by 22% (assume a linear field current/flux relationship). Vout = __________________ c) The speed is increased to 1738 RPM Vout = __________________ d) The field current is reduced by 12% and the speed is increased to 1600 RPM Vout = _________________