A 60 cm CI main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? (With Free Body Diagram)

A 60 cm CI main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? (With Free Body Diagram)

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter15: Braced Cuts

Section: Chapter Questions

Problem 15.6P

See similar textbooks

Similar questions

Water flows through the system below (see arrow direction). The saturated unit weight of the soil is 17.985 kN/m3. If a=3m, b=d=1m, c=6m and e=2.5m. Determine the effective stress at section X-X.
If the tubular shaft has an allowable shear stress of 65MPa, determine the required wall thickness of the shaft. The outer diameter of the shaft is150mm.
6.3 Determine the wall shearing stress in a pipe of diameter 100mm, which conveys water. The velocities at the half the diameter from boundary is 2 m/s. The local velocity at 20mm from the pipe wall is 1.5m/s and the flow is turbulent,
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of kz=4m/day and kx=5m/day, respectively. The difference in the head is 18 m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35 m and width of Dam =40m Determine a) the seepage flow b) the uplift pressure (kpa)at point A C) the uplift force (Kn) acting in the dam. assume that the uplift pressure under the dam varies uniformly
A single rectangular opening 10 ft (3.0 m) in height is driven in rock having strengths of fc = 18,000 lb/in2 (124 MPa) and ft=1500 lb/in2. (10.3 MPa).Rock specific gravity is 2.3.The opening is located at depth of 2000 ft (610 m) in a stress field of no lateral pressure and has a fillet ratio of h .a. Determine if the opening will fail when its width is 20 ft (6.1 m).b. Is there any benefit to reducing the width to 10 ft (3.0 m)? To 5 ft (1.5 m)?c. What is the maximum safe width of opening?
A masonry dam has a coefficient of permeability in the vertical and horizontal directions of Kz=4m/day and Kx=5m/day, respectively. The difference in the head is 18m and the distance between the base of the dam and the downstream water surface is 18m. Assume z=35m and width of dam = 40m. a. Determine the seepage flow (m3/day). b. Determine the uplift pressure (kPa) at A. c. Determine the uplift force (kN) acting in the dam. Assume that the uplift pressure under the dam varies uniformly.
Determine the pressure intensity on the base of the Dam shown. Consider without hydrostatic uplift. Unit weight of concrete is 24 kN/m^3.
A 3m by 4m rectangular area carrying a uniform load of 240 kPa is applied to the ground surfae. Compute the vertical stress ( the vertical unit pressure) increment due to their load at a depth of 6m below the ground surface using the approximate method.
An open top standpipe as shown has d = 2.5 m and 30 mm wall thickness. Determine the height ? (?? ??????) of the water that will result to a circumferential stress of 10 MPa in the wall of the standpipe. NOTE: The specific weight of water ?? is 9.81 3. Remember, pressure is equals to the product of m specific weight and height. Use 2 decimal places
A water tank, 15 m in diameter and 10 m high, isproposed for a site where there is an existing pipeline(Figure P7.26). Plot the distribution of vertical and lateral stress increases imposed by the water tank on the pipeline along one-half the circumference nearest to the tank.The empty tank’s weight (deal load) is 350 kN. Assume thewater tank is fi lled to its capacity
A retaining wall 4m high supports a horizontal granular back-fill. The unit weight of back fil is 1.65 kN/m^3. Angle of friction of soil is 35 degrees , wall friction angle is 10 degrees. Compute the Coulumbs passive pressure coefficient . Compute the passive force per unit length of wall. Compute the location of the passive force from the bottom of wall.
Pressurized water at 1.37 Mpa is stored in a steel cylindrical tank 1.4 meters in diameter. If the allowable tangential stress is 8.5 Mpa, compute the required wall thickness of the tank.