A 600 mm diameter siphon pipeline discharges water from a large reservoir. Determine the maximum possible elevation of its summit B, for a discharge of 2.7 m³/s. Where the pressure at A and C equal to atmospheric pressure as 1 bar 105 N/m² absolute. %3D And the pressure at B= 25 KN/m² absolute. Assume g= 9.81 m/s? and density of water = 1000 Kg/m³. B a. 3m Za-?? b. 2 m C. 4 m d. 5 m Zc

A 600 mm diameter siphon pipeline discharges water from a large reservoir. Determine the maximum possible elevation of its summit B, for a discharge of 2.7 m³/s. Where the pressure at A and C equal to atmospheric pressure as 1 bar 105 N/m² absolute. %3D And the pressure at B= 25 KN/m² absolute. Assume g= 9.81 m/s? and density of water = 1000 Kg/m³. B a. 3m Za-?? b. 2 m C. 4 m d. 5 m Zc

Name: A 600 mm diameter siphon pipeline discharges water from a largereserv
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 600 mm diameter siphon pipeline discharges water from a largereservoir.Determine the maximum possible elevation of its summit B, for adischarge of 2.7 m³/s.Where the pressure at A and C equal to atmospheric pressure as 1 bar =10 N/m² absolute.And

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water, issuing vertically from a nozzle having a diameter of 25 mm, flows out under a head of 30 m. If C = Cv = 0.98, determine at what constant height could the jet of water support a load of 200 N vertically from the nozzle tip?
An elbow deflects water upward and discharges it to the atmosphere at a specific rate. Determine the gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place. (gage pressure at the outlet is zero)
A 3"-diameter jet has a velocity of 110 fps. It strikes a blade moving in the same direction at 70 fps. The deflection angle is 150°. Assuming no friction, determine the final absolute velocity of the water V2 as it leaves the blade.
A cylindrical tank discharges water at 20^O C through a well-rounded orifice to hit an inclined plate as shown in the figure. Determine the components of the force exerted by the fluid jet on the plate inclined at 60^O from the horizontal.( Assume the external and internal pressures are the same)
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 30°
The three reservoirs system contains water. If L1 = 2000 m, f 1= 0.013, D1 = 1m; L2 = 2300 m, f2 = 0.02, D2 = 0.60m; and L3 = 2500 m, f = 0.023, D3 = 1.20m. Compute Q3 in m3/s.
A horizontal nozzle discharges water into the atmosphere as shown in the figure. the relative pressure at point 1 equal to ?1 = 18 ??? . A. A Pitot tube connected to a mercury manometer is inserted into the flow. in the area section A1 indicating a height difference ℎ = 0.01 m. For this reading indicated in the Pitot tube, determine the velocity in the A1 area section of the nozzle. B. For the dimensioning of the anchor block it is necessary to determine the force that the nozzle applies over the fluid. Calculate the component of this force in the x direction. Data: ?1 = 0.070 ?; ?2 = 0.060 ?; ? = 30°; ??? = 13.6
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
The diameter of a pipe gradually reduces from 1 m to 0.7 m. The pressure intensity atthe center line of 1 m section is 8and rate of flow of water through the pipe is600 liters/s.,I. Find the intensity of pressure at the center line of 0.7 m section.II. Determine the force exerted by flowing water on transition of the pipe.
In the dam shown in the figure, the water flows at the entrance of the conduitwith a speed of 0.4 m/s and exits at 9.5 m/s the generator building, 175 m belowof the socket Considering that the temperature of the water in the dam is 28 °C andthat the gravitational acceleration of the place is 9.78 m/s2 , determine:a) The pressure difference between the outlet and the inlet of the intake.b) The diameter of the duct at the outlet connected to the generator building, if theinput area in the socket is 0.7 m2. .
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Determine(a) Thevelocity(m/s)atsectionB.(b) Thepressure(kPa)atpointB.(c) FP (x-direction),(d) FP (y-direction),(e) The magnitude and direction of FRX of the force required to hold the bend in place.(f) The magnitude and direction of FRY of the force required to hold the bend in place.Forces are to be expressed in Newtons.
a)Determine the value of h in the siphon shown if velocity at C was 11.7 m/s. Diameter of the pipe is 2.5cm. b) Determine the pressure at point B.