Problem 8: Complete the design of the beam shown in figure below to carry a large hydraulic motor. The beam is attached to the two side rails of the frame of a truck. Because of the vertical accelerations experienced by the truck, the load on the beam varies from 1200 lb upward to 5000 lb downward. One-half of the load is applied to the beam by each foot of the motor. Hydraulic motor Side rail of truck Beam to be designed -16 in 16 in-

Problem 8: Complete the design of the beam shown in figure below to carry a large hydraulic motor. The beam is attached to the two side rails of the frame of a truck. Because of the vertical accelerations experienced by the truck, the load on the beam varies from 1200 lb upward to 5000 lb downward. One-half of the load is applied to the beam by each foot of the motor. Hydraulic motor Side rail of truck Beam to be designed -16 in 16 in-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.11P: A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
A bevel gear is attached to a shaft supported by self-aligning bearings at A and B and is driven by a motor. The axial force, radial force, and tangential force are known. Assume the weight of the gear and shaft is negligible and that the bearing at A takes all the thrust load A) Draw (to scale) axial load, shaft torque, shear force(x-y and x-z), and bending moment(x-y and x-z)diagrams for the shaft B)Determine the values of axial load and torque along the shaft
PROBLEM: 4 A helical spring is made from a wire of 11 mm diameter and is of outside diameter 101 mm. The spring has 8 numbers of active coils. If the permissible stress in shear is 480 N/mm2 and the modulus of rigidity is 87 KN/mm2. Find the axial load which the spring can take and the deflection produced.
A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side.
Problem 4:Sketch the distribution of the shear stress due to torsion in a circular shaft. (simple sketch of shear stress “τ” vs. shaft radius “ρ” for the elastic region)
The machine element located at the C point in the transmission system shown in the figure creates radial and axial loads. These loads; Fr: 500 daN, Fa = 250 daN in addition to thisDue to the weight of the machine element, a further 100 daN load is exerted on the shaft. The loads in the system are met by A and B single row ball radial roller bearings. By evaluating what is given;a-) Calculate the forces acting on the bearings and the required shaft diameter.b-) Choose the most optimum bearing so that the life of the A bearing will be at least 4000 hours. For the shaft material in the system; σsafety=7daN/mm2 bearings will operate at 1000 rpm rotation speed. Important Note: Axial Load will be borne by A bearing.
A typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: mean coil diameter = 100 mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: mean coil diameter = 75 mm No. of turns = 20Both the springs are of equal initial length when unloaded. Ifthe working stress for each spring is to be same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following:a. Diameter of steel wire for inner spring. b. Stiffness of inner springc. Stiffness of the compound spring. I need answer ASAP. Thank you!
Application of the limb numbered 2 in order to keep the crank-connecting rod mechanism shown in the figure in balance.find the required torque.
A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic shock cord having axial rigidity EA = 2.3 kN (see figure). If the jumpoff point is 60 m above the water, and if it is desired to maintain a clearance of 10 m between the jumper and the water, what length L of cord should be used?
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.
Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.