A 84-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 6v2/2g, and the head loss from point 2 to point 3 is 2v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.327 kPa. Use y, = 5 m., and y, = 7 m. ROUND OFF TO TWO DECIMAL PLACES. Siphon Oil y2

A 84-mm-diameter siphon is drawing oil (SG = 0.85) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 6v2/2g, and the head loss from point 2 to point 3 is 2v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.327 kPa. Use y, = 5 m., and y, = 7 m. ROUND OFF TO TWO DECIMAL PLACES. Siphon Oil y2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The water tank is below a constant level at depth h rectangular hole a x b. We close the opening with an immersion wall from the upper edge of the hole by a distance x. Given: h = 0.85 m, a = 0.4 m, b = 0.7 m. Determine: by what distance x do we have to move the immersion wall, to reduce the flow 3 times, what will be the flow Q1 at submerged wall by x, Reynolds number Re in flow, nature of flow.
A sluice gate flows into a horizontal channel as shown in the figure. Determine the flow through the gate per meter width when y=1.0m and d1=6m. Assume that the pressure distributions at section 1 and 2 to be atmospheric and neglect losses in the channel. Use coefficient of contraction Cc= .85 and coefficient of velocity is Cv=.95.
A 4.1 m diameter tank having equal layers of water, oil(SG=0.87), and another liquid with SG=1.74, with each layer is 0.84 m in height is being observed. Find the gage pressure(in kPa) at the bottom of the oil layer.
PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at C was 38.38 fps. Diameter of the pipe is 1 inch. (b) Determine the pressure at point B in psi.
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
4. A reservoir supplies water to a horizontal 6′′ pipe 800 ft long. The pipe flows full and discharges into the atmosphere at the rate of 2.23 cfs. What is the pressure in psi midway in the pipe, assuming the only lost head is 6.20 ft in each 100 ft of length? indicaye free body diagram
A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure below. The loss of head from A to 1 is equal to the velocity head in the 150-mm pipe and the loss of head from 2 to B is 15 times the velocity head in the 100-mm pipe. Determine the horsepower output of the pump and the pressure heads at 1and 2 when the velocity of flowing water at the 150 mm diameter pipe is 1.5 m/s.
Given the figure below, (a) determine the value of h in the siphon shown if velocity at C was 38.38 fps. Diameter of the pipe is 1 inch. (b) Determine the pressure at point B in psi.
Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid‐point of the pipe). SN=21
2. A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in SI units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.). Head losses in pipe: 1 to 2: 3.00 m 2 to 3: 9.00 m 3 to 4: 4 to 5: 18.00 m 6.00 m 1 W.S. ELEV. 140 ELEV. 128 M ELEV. 15M 5 6
The open tank filled with a liquid in full as shown in the figure below has the height of h = 6.00 m. The inclined angle of the inclined wall is = 45.00 °. The width (perpendicular to the screen) of the inclined wall is w = 20.00 m. The specific weight of the liquid is = 9.81 kN/m3. (3) For the inclined wall, determine the vertical depth to the center of pressure._________ (m)
3.Water flows from a tank through 22 meters of 150–mmdiameter pipe and then discharges into air as shown in the figure. The flow of water in the pipe is 120 L/s.Assume n = 0.013 and neglect minor losses. a. Find the velocity of flow in the pipe in m/s. b. Determine the total head loss in the pipe in meters. c. Calculate the pressure at the top of the tank in kPa.