A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m Patm

A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v', the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m Patm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The water tank is below a constant level at depth h rectangular hole a x b. We close the opening with an immersion wall from the upper edge of the hole by a distance x. Given: h = 0.85 m, a = 0.4 m, b = 0.7 m. Determine: by what distance x do we have to move the immersion wall, to reduce the flow 3 times, what will be the flow Q1 at submerged wall by x, Reynolds number Re in flow, nature of flow.
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
A sluice gate flows into a horizontal channel as shown in the figure. Determine the flow through the gate per meter width when y=1.0m and d1=6m. Assume that the pressure distributions at section 1 and 2 to be atmospheric and neglect losses in the channel. Use coefficient of contraction Cc= .85 and coefficient of velocity is Cv=.95.
Water at 60°F is siphoned between two tanks as shown in Figure P8.27. The connecting tube is 2.0 in. diameter smooth plastic hose 20 f t long. Find the volume flow rate and the pressure at point P, which is 8 f t from the entrance to the tube. Ignore minor losses. (To begin, assume a friction factor, then iterate.)
A pump draws water from reservoir A and lifts it to reservoir B as shown in Figure below. The loss of head from A to 1 is equal to the velocity head in the 150-mm pipe and the loss of head from 2 to B is 15 times the velocity head in the 100-mm pipe. Determine the horsepower output of the pump and the pressure heads at 1and 2 when the velocity of flowing water at the 150 mm diameter pipe is 1.5 m/s.
Given the figure below, (a) determine the value of h in the siphon shown if velocity at C was 38.38 fps. Diameter of the pipe is 1 inch. (b) Determine the pressure at point B in psi.
PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at C was 38.38 fps. Diameter of the pipe is 1 inch. (b) Determine the pressure at point B in psi.
3.Water flows from a tank through 22 meters of 150–mmdiameter pipe and then discharges into air as shown in the figure. The flow of water in the pipe is 120 L/s.Assume n = 0.013 and neglect minor losses. a. Find the velocity of flow in the pipe in m/s. b. Determine the total head loss in the pipe in meters. c. Calculate the pressure at the top of the tank in kPa.
A 4.1 m diameter tank having equal layers of water, oil(SG=0.87), and another liquid with SG=1.74, with each layer is 0.84 m in height is being observed. Find the gage pressure(in kPa) at the bottom of the oil layer.
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals
2. A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in SI units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.). Head losses in pipe: 1 to 2: 3.00 m 2 to 3: 9.00 m 3 to 4: 4 to 5: 18.00 m 6.00 m 1 W.S. ELEV. 140 ELEV. 128 M ELEV. 15M 5 6
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure