A 915 mm diameter driving pulley is used to drive 1,220 mm pulley. The center to center distance between the two pulleys is 3.5 mm and the output of the driven shaft is 85 HP. If a leather belt is used with a belt speed of 1,300 m/min coefficient of friction is 0.28, percent slip is 1.5% on each pulley, and loss due to friction on each shaft is 6%, calculate: (a) The rpm of each shaft: Ans. N1 = 459.13 rpm; N2 = 344.35 rpm (b) Difference in belt tension: Ans.(F1 - F2) = 3.11 kN (c) Size of 9.5 mm thick leather belt: Ans. b = 0.2475 mm; L = 10.6792 m

A 915 mm diameter driving pulley is used to drive 1,220 mm pulley. The center to center distance between the two pulleys is 3.5 mm and the output of the driven shaft is 85 HP. If a leather belt is used with a belt speed of 1,300 m/min coefficient of friction is 0.28, percent slip is 1.5% on each pulley, and loss due to friction on each shaft is 6%, calculate: (a) The rpm of each shaft: Ans. N1 = 459.13 rpm; N2 = 344.35 rpm (b) Difference in belt tension: Ans.(F1 - F2) = 3.11 kN (c) Size of 9.5 mm thick leather belt: Ans. b = 0.2475 mm; L = 10.6792 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a steel gear wheel that is shrunk onto the hollow shaft has an outer radius of 150 mm. The maximum allowable tangential stress developed by shrinking the gear wheel onto the hollow shaft is 200 MPa. The length of hub parallel to the shaft axis is 200 mm, and the coefficient of static friction between the hub and the shaft is 0.40. Determine the maximum torque that may be transmitted by the gear wheel without slipping on the shaft.
4. The weight of each wheel of a motor driven traveling crane moving at 600fpm is 5800 Ibs. If the coefficient of rolling friction is 0.05, find the horsepower required to overcome friction. 5. Compute the force necessary to move a 6000 lbs supported on four wheels of 2.5 ft diameter, assuming the coefficient of rolling friction to be 0.007.
A mechanic is lifting a car of 2000kg using a screw jack as he applies a force of 100 N. The screw jack handle is 600 mm, and the screw pitch is 10 mm. Calculate the following; Mechanical advantage Velocity ratio Efficiency
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
Two identical pulleys with diameter of 711 mm, are mounted on two parallel shafts for flat belt drive system. The maximum permissible tension in the belt is 2,691 N and the coefficient of friction between belt and pulley is 0.31. The centrifugal tension acting on the belt is 887 N. Calculate the power that can be transferred in Watts if the rotational speed of the driving pulley is 978 r.p.m.
Find the power lost in friction assuming i)uniform pressure and ii)uniform wear, when a vertical shaft of 100 mm diameter rotating at 150 RPM rest on a flat and foot step bearing . The coefficient of friction is equal to 0.05 and shaft carries a vertical load of 15kN.
A pulley, 610 mm. in diameter, transmits 40 kW at 500 rpm. The arc of contact between the belt and the pulley is 144 degrees, the coefficient of friction between the belt and the pulley is 0.35 and the safe working stress of the belt is 2.1 MPa. Find the width of the belt if its thickness is 6 mm.
An open belt drive connects two pulleys 1.2 m and 0.5 m diameter on parallel shafts 3.6 m apart. The belt has a mass of 1kg/m length and the maximum tension in it is not to exceed 2kN. The 1.2 m pulley, which is the driver, runs at 200 rpm. Due to the belt slip on one of the pulleys, the velocity of the driven shaft is only 450 rpm. If the coefficient of friction between the belt and pulley is 0.3, find: 1. Torque on each of the two shafts, 2. Power transmitted, 3. power lost in friction, and 4. efficiency of the drive.
Metal plate A, shown in Fig. 6.70, is attached to block B by a double square threaded screw, which has a 1/16 inch spacing. The mean radius of the thread is 1/4 in. The coefficients of static and kinetic friction for the threads are 0.30 and 0.25, respectively, and the friction between plate A and the screw head is negligible. The screw is tightened using a torque wrench. Estimate the clamping force on plate A if the torque wrench indicates a measurement of 40 lb.ft a). when the screw is about to turn b) when it is turning.
From the rotating shaft shown below, a force 100 N was pulled to reduce the shaft’s angular speed through its cables. What is the maximum cable tension if the shaft rotates in a counterclockwise direction? Use coefficient of friction on shaft equal to 0.2.
A flat belt drive connects two pulleys 5 meters apart. The 2m pulley diameter driver rotates at 350rpm, and the driven pulley has a diameter of 1.5m. The thickness and the mass of the belt drive is 5mm and 0.6kg respectively. The coefficient of friction between the belt and the pulley is 0.25. The belt experience 3% of slip during power transmission with a maximum tension of 1200N.Calculate the speed and torque of the driven shaft.
Power Transmission A power transmission system consists of a motor connected to a pulley and a belt. The motor has a power output of 10 kW and operates at a speed of 1200 rpm. The pulley connected to the motor has a diameter of 300 mm, while the pulley connected to the driven shaft has a diameter of 600 mm. The belt used has a coefficient of friction of 0.3. Determine the maximum torque that can be transmitted by the system and the rotational speed of the driven shaft.