7. Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience. o (ksi) e (in. /in.) 33.2 0.0006 45.5 0.0010 49.4 0.0014 0.0018 51.5 53.4 0.0022

7. Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience. o (ksi) e (in. /in.) 33.2 0.0006 45.5 0.0010 49.4 0.0014 0.0018 51.5 53.4 0.0022

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please annotate the attached stress strain graph of 0.9% carbon steel to show the different phases. From the graph work out the following: 1) modulus of elasticity 2) tensile strength 3) the ductility in % elongation 4) yield strength at a strain offset of 0.002
a 200mm long rod with a diameter of 50mm is loaded with a 4kN weight.the rod finale length 201.314mm and finale diameter 42mm.the load at the fracture is 2.5kN and the maximum load is 3.5kN. Calculate to third decimal and determine the folliwing 1.stress 2.strain 3.limit of proportionality 4.percentage of reduction in area 5.percentage elogation
A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table. Plot the stress–strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture stress. Use a scale of 25 mm = 140 MPa and 25 mm = 0.05 mm/mm. Redraw the elastic region, using the same stress scale but a strain scale of 25 mm = 0.001 mm/mm.
A mild steel bar went through a tensile test conducted at the University of San Carlos Mechanical Engineering Laboratory. The following data was obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm iii. Load at the elastic limit = 250 kN iv. Extension at a load of 150 kN = 0.21 mm v. Maximum load = 380 kN vi. Total extension = 60 mm vii. Diameter of the rod at the failure = 22.5 mm Determine the Young’s modulus, the stress at the elastic limit, the percentage elongation, and the percentage decrease in area.
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mm diameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) :
The stress-strain diagram of a reinforcement steel having a cross-sectional diameter of 12 mmdiameter and 100 mm gage length is determined after its tensile strength test as follows. Based on the stressstrain diagram determine the followings properties of the material (Poisson’s ratio of the material is 0.32) : a) Modulus of elasticityb) Yield strengthc) Toughnessd) Resiliencee) Shear modulusf) Bulk modulusg) Ductility as described bypercent change in length
Which one(s) of the following about G, shear modulus of elasticity of a material are correct? select all which are correct. G is also called the modules of rigidity. G is related to the modulus of elasticity E and Poisson’s ratio . G is usually smaller than Young's modulus E for the same material. G is the ratio of shear stress to shear strain when the material's proportional limit in shear has not been exceeded.
In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17 kips. Determine the ratio of the shear modulus to the modulus of elasticity of a material whose Poisson's ratio is 0.25.
PROPAGATION OF ERRORS Determine the range of values to which the strain will be calculated.F = 150000 +/- 150 lbfSide length = 1.2 +/- 0.025 inModulus of Elasticity = 25000 +/- 11.5 ksiDetermine the relative error. Is it above or below the accepted 5% relative error?
The ply stress σα was calculated for AS1/3501-6 Graphite/Epoxy laminates [0/+-45]s under load with N1=10,000 N/m and N2=N6=0. When the strength of this material is as follows, determine the stability of the laminate according to the maximum stress theory.
Hooke's Law defines the stress-strain relationship for an elastic material: s=Ee, where E= . A)The strain of the material at yield B)The percent elongation at failure C) A constant neutralization reducing the units to zero D) a constant proportionality called the modulus of elasticity
A bar has a length of 200 mm and cross-sectional area of 7500 mm2. Determine the modulus ofelasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm.The material has linear-elastic behavior.