A: A single core cable covered by the lead, if the radius of the cadactor is r and the insulator consists of one layer draw the cross section of this underground cable and show where will be the maximum and minimum electric stress and how many electric stresses which ?can be accounted for this cable

A: A single core cable covered by the lead, if the radius of the cadactor is r and the insulator consists of one layer draw the cross section of this underground cable and show where will be the maximum and minimum electric stress and how many electric stresses which ?can be accounted for this cable

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

Determine the ohms-per-mil-foot of an aluminum conductor located in an area with a temperature of 104F (40C). Use the NEC to determine the ampacity of the following conductors.
Why do static charges accumulate on insulator materials only?
One thousand circular mils or 1 kcmil is sometimes designated by the abbreviation MCM75C. Data for commercial bare-aluminum electrical conductors lists a 60 Hz resistance of 0.0080 ohm per kilometer at for a 793-MCM AAC conductor. Determine the cross-sectional conducting area of this conductor in square meters. Find the 60 Hz resistance of this conductor in ohms per kilometer at 50C.
What are interpoles, and what is their purpose?
A 415 single core cable has a conductor diameter of 0.5 cm and a sheath of inside diameter 3 cm. In cable insulation, find: (i) minimum stress (in V/cm); (ii) maximum stress in (V/cm); (iii) Describe where these minimum and maximum stress will occur in cable insulation?; (iv) Suggest what should be the minimum dielectric strength (in V/mm) of the cable insulation to avoid any breakdown of the given cable
The inner conductor of a long coaxial cable has radius a. The inner radius of the outer conductor is b. Inner conductor V0, outer conductor at 0 potential. Determine the electric potential and electric field strength in the insulating material.
The conductivity of a material is essentially expressed by the product of the number of free carriers and the mobility of these carriers. Explain why the conductivity of conductors increases at higher temperatures, while an opposite trend is seen with metals.
A string of 8 suspension insulators is to be fitted with a grading ring. If the pin to earth capacitances are all equal to C, find the values of line to pin capacitances that would give a uniform voltage distribution over the string.
A coaxial cable of consists of two concentric cylindrical conductors. The region between the conductors is completely filled with polyethylene plastic. The radius of the inner conductor is 0.50 cm, the radius of the outer conductor is 1.75 cm, and the length of the cable is 15 cm. The resistivity of the plastic is 1013 Ω • m. Calculate the resistance of the plastic if the electric field is applied across the ends of the conductor.
A lead conductor is 5cm in length and 8 sq. cm in cross-sectional area. The terminals to be joined by this conductor are 8 cm apart. Hence, the conductor was pounded and reshaped until it is 8 cm long. If the resulting conductor has uniform cross-sectional area, determine the resistance. Resistivity of leads is 22x10^-8 Ω-m.
A lead conductor is 5cm in length and 8 sq. cm in cross-sectioned area. The terminals to be joined by this conductor are 8 cm apart. Hence, the conductor was pounded and reshaped until it is 8 cm long. If the resulting conductor has uniform cross-sectional area, determine the resistance. Resistivity of lead is 22x10^-8 Ω-m.
Neglecting losses and fringing effects and assuming the substrate of a stripline to have a thickness of 0.42 (mm) and a dielectric constant of 2.83, determine the required width (in mm) of the metal strip in order for the stripline to have characteristics resistance of 78 Ohms. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.