An FIR digital filter has the following specification Passband frequency ≥ 50 Hz ≤ 40 Hz Stopband frequency Passband ripple 0.01 dB Stopband attenuation 40 dB Sampling frequency 100 Hz a) Sketch the tolerance scheme of the ideal and practical filter. b) Calculate the first three coefficients of FIR digital filter using hanning window. c) Draw the realization block diagram of this filter with three coefficients using transvers structure.

An FIR digital filter has the following specification Passband frequency ≥ 50 Hz ≤ 40 Hz Stopband frequency Passband ripple 0.01 dB Stopband attenuation 40 dB Sampling frequency 100 Hz a) Sketch the tolerance scheme of the ideal and practical filter. b) Calculate the first three coefficients of FIR digital filter using hanning window. c) Draw the realization block diagram of this filter with three coefficients using transvers structure.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Suppose we have a first-order lowpass filter that is operating in sinusoidal steady-state conditions at a frequency of 5 kHz. Using an oscilloscope, we observe that the positive-going zero crossing of the output is delayed by compared with that of the input. Determine the break frequency of the filter.
We have a band-pass filter, where the system has a sampling rate of 48 ksps, the filter will allow the spectral components between the sequences Fa=12kHz and Fb=16kHz and will be used in a 32-tap FIR filter,now center the response of the band pass filter at frequency 0 and plot the frequency response of the resulting low pass filter
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
The input power of a filter is 200 mW and its output power in dBm scale is 20 dBm. Accordingly, a) Does this filter provide Attenuation or Gain in a circuit? Why is that? b) What is the value of the power loss or gain in this filter?
Determining theOrder of a Butterworth Filter1. Determine the order of a Butterworth filter that has a cutoff frequency of1000 Hz and a gain of no more than −50 dB at 6000 Hz.2. What is the actual gain in dB at 6000 Hz?
(a) as shown for a maximally flat second-order low-pass filter with fo =25 kHz, using the circuit as shown. Assume C =0.005μF.What is the filter bandwidth? (b) Use frequency scaling to change fo to 50 kHz.
Q1- Design a 3 tap FIR band-stop filter with Stopband cut-off frequency fc1=3KHz, fc2=5.5KHz and Sampling frequency fs=20KHz if the filter order N=14 using the Hamming window function.
"A low pass filter has an input of 12 V, 1000 Hz signal. The filter is consists of a 1500 Ohms resistor and 0.15 micro Farad capacitor. To assess the performance of filter, determine the following: (i) Capacitive reactance (in Ohms) (ii) Amplitude of the output signal (in Volts); (iii) Corner frequency (in Hertz) (iv) Suggest the changes in filter design, if the input signal required to being more and more attenuated
Design a high pass filter with a cut of frequency of K1 and a passband gain of K2. Take K1 equal to 27 in kHz and K2 is the 7 (b) Plot the Bode plot of the frequency response of the designed circuit using a python script and validate your answer. (c) How would you increase the passband gain by a factor of five without changing the cutoff frequency?
A numerical filter design problem is given. This filter, which is desired to be causal and stable, suppresses 0 and π frequencies (having zero at z1=1 and z2=-1 points) and passes π/2 and –π/2 frequencies (p1=rejπ/2 and p2=re-jπ/2). have poles at the points) is desired. By choosing an appropriate r-value, the filter: a. give the system function and frequency response,b. Give the unit impulse response,c. Give the difference equation.
It is known that a low-pass Butterworth filter has order N = 4. Accordingly, the mentioned analogueFind the transfer function H(s) of the filter . If the filter degree is ¸even Continue the ωc value as a letter.
Let the impulse response of a filter be ℎ[?] = {ℎ[0] = −0.5, 0.5}a) Calculate the frequency response ?(???). Is it a low-pass or a high-pass filter? Plot boththe magnitude and phase responses.b) Obtain the I/O relation for this filter.c) Is this a causal filter? Explain your answer.