A balance Y-connected load of ( 3 + j8 ) ohms per phase is supplied by a balanced three- phase, 60 Hz, positive phase sequence source. If Vsc = 133.6998 + j159.3372 volts, determine the following: (Answers in complex numbers must be expressed in POLAR FORM) a. VAB b. Vca c. Line current lA d. Line current ls e. Line current lc f. Total real power of the load g. Total reactive power of the load

A balance Y-connected load of ( 3 + j8 ) ohms per phase is supplied by a balanced three- phase, 60 Hz, positive phase sequence source. If Vsc = 133.6998 + j159.3372 volts, determine the following: (Answers in complex numbers must be expressed in POLAR FORM) a. VAB b. Vca c. Line current lA d. Line current ls e. Line current lc f. Total real power of the load g. Total reactive power of the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
The IAC current of a balanced three-phase delta connected load is known as 10 Amps (-10 degrees) and the VAB voltage as 20 Volts (10 degrees). Accordingly, calculate the following expressions by considering the positive phase sequence. A) IAB=? B)load impedance=? C)IBC=?
A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral current
In the above figure, a single line model of a three-phase power system is given. Base power 50MVA, base voltage 13.8kV according to its value, a) Per-unit values of power system circuit elements according to the given base power and base voltage values. calculate. b) The perunit you calculate by drawing the equivalent impedance circuit for one phase of the power system given in the figure. show on the values.
A balanced 3-phase Y-connected source has using positive phase sequence, ?an = 390∠30˚ ?. Find the complex expression of voltage Eab. Circuits Problem 1
4) State the relation between line and phase values of voltage and current for 3-pha se DELTA connected load .state the equation for active, reactive power consumed by 3-phase load.
A balanced delta connected load of 13+j16 ohm per phase is connected at the end of a three-phase line. The line impedance is 2+j11 ohm- per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
A three-phase, 3-wires CBA System alternator, sending 3-phase voltages of 339.4 volt to the lines, having a delta connected load, with VCA is the reference vector. ZBC = 12.99 – j7.5 ZCA = 8.66 + j5 ZAB = 10 + j0 Determine the phase and line current b) draw the phasor diagram and c) true power generates by the generator neglect the line losses.
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…
A balanced three-phase source with grounded neutral has line-to-neutral voltages of 120 volts with an-bn-cn sequence. This source has an internal series impedance of 0.1+j1.5 ohms per phase. It supplies power to an unbalanced three-phase wye, neutral grounded, load with impedances: Zan = 40+j30; Zbn = 36-j15; Zcn = 18+j24 ohms. If there is a single-line-to-ground fault at line a load-side, what is the magnitude of the fault current in amperes?