A beam 6 m in length is placed on a support so that it pivots at the point of the support. An 8 N weight is placed on one end, which is 1 m from the pivot point, and a 1 N weight is placed at the other end. To balance the beam, what is the minimum weight required to be added? ☐☐☐0 5 N 7M 0.6 N 1.33 N

A beam 6 m in length is placed on a support so that it pivots at the point of the support. An 8 N weight is placed on one end, which is 1 m from the pivot point, and a 1 N weight is placed at the other end. To balance the beam, what is the minimum weight required to be added? ☐☐☐0 5 N 7M 0.6 N 1.33 N

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 12PE: Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the...

See similar textbooks

Similar questions

The upper leg muscle (quadriceps) exerts a force of 1250 N, which is carried by a tendon over the kneecap (the patella) at the angles shown in Figure 9.38. Find the direction and magnitude of the force exerted by the kneecap on the upper leg bone (the femur). Figure 9.38 The knee joint works like a hinge to bend and straighten the lower leg. It permits a person to sit, stand, and pivot.
Suppose a 900-kg car is on the bridge in Figure 9.34 with its center of mass halfway between the hinges and the cable attachments. (The bridge is supported by the cables and hinges only.) (a) Find the force in the cables. (b) Find the direction and magnitude of the force exerted by the hinges on the bridge.
Two children of mass 20.0 kg and 30.0 kg sit balanced on a seesaw with the pivot point located at the center of the seesaw. If the children are separated by a distance of 3.00 m, at what distance from the pivot point is the small child sitting in order to maintain the balance?
What is the mechanical advantage of a nail puller similar to the one shown in Figure 9.23 —where you exert a force 45 cm from the pivot and the nail is 1.8 cm on the other side? What minimum force must you exert to apply a force of 1250 N to the nail? Figure 9.23 A nail puller is a lever with a large mechanical advantage. The external forces on the nail puller are represented by solid arrows. The force that the nail puller applies to the nail ( Fo ) is not a force on the nail puller. The reaction force the nail exerts back on the puller ( Fn ) is an external force and is equal and opposite to Fo. The perpendicular lever arms of the input and output forces are li and l0
Suppose a horse leans against a wall as in Figure 9.31. Calculate the force exerted on the wall assuming that force is horizontal while using the data in the schematic representation of the situation. Note that the force exerted on the wall is equal in magnitude and opposite in direction to the force exerted on the horse, keeping it in equilibrium. The total mass of the horse and rider is 500 kg. Take the data to be accurate to three digits.
A sandwich board advertising sign is constructed as shown in Figure 9.35. The sign's mass is 8.00 kg. (a) Calculate the tension in the chain assuming no friction between the legs and the sidewalk. (b) What force is exerted by each side on the hinge?
Even when the head is held erect, as in Figure 9.41, its center of mass is not directly over the principal point of support (the atlanto-occipital joint). The muscles at the back of the neck should therefore exert a force to keep the head erect. That is why your head falls forward when you fall asleep in the class. (a) Calculate the force exerted by these muscles using the information in the figure. (b) What is the force exerted by the pivot on the head?
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
A 5.00 m–long uniform diving board that weighs 250.0 N is supported by two pillars. One pillar is at the left end of the diving board, and the other is 1.30 m away as shown in the figure below. Find the forces exerted by the pillars when a 75.0 kg diver stands at the far end of the board.
Q10 In the figure, one end of a uniform beam of weight 310 N is hinged to a wall; the other end is supported by a wire that makes angles θ = 27° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam.
A hungry bear weighing 730 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see the figure below). The beam is uniform, weighs 200 N, and is 7.00 m long, and it is supported by a wire at an angle of θ = 60.0°. The basket weighs 80.0 N. (a) If the wire can withstand a maximum tension of 875 N, what is the maximum distance the bear can walk before the wire breaks?
3. Two people carry a heavy electric motor by placing it on a light board 2.00 m in length. One person lifts at one end with a force of 700N, and the other lifts the opposite end with a force of 500N. What is the weight of the motor, and where along the board is its center of gravity located? (Note: The center of gravity of an object is the point where the weight passes through.) Draw the FBD.