A beam ABCDE has 8 m long, has a simply supported at A and D, and AB=BC=CD=DE= 2 m, loaded with a uniformly distributed load on the 4 m span CE is 39 KN/m with 39 KN a concentrated load on C and moment on B is 39 KN.m. Draw the Shear Force and Bending Moment diagrams stating the important values and determine the maximum Bending moment value and its position.

A beam ABCDE has 8 m long, has a simply supported at A and D, and AB=BC=CD=DE= 2 m, loaded with a uniformly distributed load on the 4 m span CE is 39 KN/m with 39 KN a concentrated load on C and moment on B is 39 KN.m. Draw the Shear Force and Bending Moment diagrams stating the important values and determine the maximum Bending moment value and its position.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter5: Beams And Frames: Shear And Bending Moment

Section: Chapter Questions

Problem 53P: For the beam shown: (a) determine the distance a for which the maximum positive and negative bending...

See similar textbooks

Similar questions

The beam AC is simply supported at A and C and subject to the uniformly distributed load of 300 N/m plus the couple of magnitude 2700 N ⋅ m as shown in figure. Write the moment equation between A and C. Draw the shear and moment diagram. Determine the maximum shear and flexural stress of the beam with a rectangular cross section of 150mm x 250mm.
The shear force of the beam, whose loading and span conditions are given in Figure 1, and draw bending moment diagrams. q(kN/m) =10 P(kN)= 21 M(kN.m) = 6 L1(m)= 3.5 L2(m)= 1.5
Construct the shear-force and bending-moment diagrams for the beam shown. Assume a = 3.2 ft, b = 6.4 ft, c = 3.2 ft, w = 1180 lb/ft, and P = 3300 lb. Part 1 Determine the vertical reaction forces at B and D.Answer:By = lbDy = lb
The shear force of the beam,whose loading and span conditions are given in Figure 1, and draw bending moment diagrams q=2 kN/m P=27kN M=6kN L1=2.5m L2=1.5m
(a) Figure Q2 shows a frame with tie rod at joint B and C. The beam carries a concentratedload 300kN at span BC. Analysis and sketch the shear force and bending-momentdiagram for the entire frame.
Determine the bending moment M in the cantilever beam at the point located 1.44 ft. to the right of point B. The ground reactions and shear-force diagram are shown. a. 8.53 kip-ft b. 10.60 kip-ft c. 6.55 kip-ft d. 7.44 kip-ft e. 11.56 kip-ft
For the beam shown in figure below, draw the shear and moment diagrams: 1- Due to applied loads (without support settlement). 2- Due to support settlement of 60 mm downward at support B (without loads). Take the stiffness El as 12000 kN.m?. 50 kN SKN/m
If the beam is subjected to an internal moment of M = 40 kN . m, determine theresultant force caused by the bending stress distribution acting on the top flange A.
For the beam below, the support reactions at QA and B have deen calculated and given as below. Continue from shear force diagram generated from last problem, generate bending moment diagram and calculate the max bending moment along the beam: ____ KN m. Calculate your answer to 1 decimal place.
1. Calculate the moment at right end of span BC (MCB) in kN.m.0 2. Calculate the shear force at left end of span AB in kN.m.0 3. Calculate the shear force at right end of span AB in kN.m.0 4. Calculate the shear force at left end of span BC in kN.m.0
The simple beam AB, shown below, supports a concentrated load of 6 kN and a segmentof non-uniform load of intensity varies from 1 kN/m to 3 kN/m at point B.1- Draw the shear force and the bending moment diagrams for the beam.2- Determine the shear force (V) and bending moment (M) at a cross section located 3.0 m from the support A
A truss is loaded with nodal force at C as shown TOS-003. If the truss members have identical rectangular section of 5 cm x 8 cm, with E = 70 GPa, compute the vertical displacement at joint C .