as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane stress element. b) Find the principal stresses and the maximum shear stress diameter =20mm 120 mm occurring at point A with their planes. SKN 70mm TKN 2KN

as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane stress element. b) Find the principal stresses and the maximum shear stress diameter =20mm 120 mm occurring at point A with their planes. SKN 70mm TKN 2KN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.18P: -18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a)...

See similar textbooks

Related questions

Q: A) Find the principal Stresses B) Find the Maximum Shear Stress 30 MAa $45 MPa 60 MPa

Q: A point on a thin plate is subjected to the two stress components as shown in Figure 7. Determine…

A: For the first element on the left, the sign convention is:

Q: 1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr’s circle…

Q: The state of stress in a material is given in the figure. Maximum principal stress will be 45 45 5 5…

A: Given, Tensile stress in x-direction = σx = 5 units Tensile stress in y-direction = σy = 5 units…

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A: A perpendicular force applied on a body per unit area is referred to as a stress. There are three…

Q: QUESTION 2 a) An element in plane stress is subjected to compressive stresses o, and tension…

A: Calculated corresponding average stress and maximum shear stress or radius R. Calculated principal…

Q: A member is subjected to a major stress of 110 MPa (tensile), minor stress of 40 MPa (compressive)…

Q: For the stress state shown. Ox = 40 MPa MPa Oy = 80 MPa Txy %3D 65 Oy Txy Using Mohr's Circle, a)…

Q: Q2) An element in a plane stress is oriented at an angle 0 = 60° CCW direction. On the inclined…

A: Normal stress Normal stress is the stress occurred when it is subjected to axial load. Shear…

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: 2 -1 o =|-1 2 1 -1 2 -1 Find (a) Principal stress (b) Principal directions (c) Invariant

A: TO FIND: (a) Principal stress (b)principal direction (c) Invariants GIVEN: stress tensor:…

Q: 1. A point in a strained material is subjected to a tensile stress of 120 MPa and a clockwise shear…

Q: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind…

A: Given Data σx=20 kpsiσy=-10 kpsiτxy=-8 kpsi Draw the diagram

Q: Principal stresses:σ1=31.69 MPa σ2=−30.56 MPa Maximum in−plane stress: σmax=31.69 MPa

Q: In the figure, the normal stresses oa = 70 MPa, o, = 50 MPa, oc = 110 MPa on the faces of the…

A: Given that, σa=70 MPa,σb=50 MPa,σc=110 MPa,α=60°,β=45°, The general form of the equation of stress…

Q: The principal tensile stress at a point across two mutually perpendicular planes are 100 N/mm2 and…

A: Write the given data with suitable variables: σx=σ1=100 N/mm2σy=σ2=40 N/mm2θ=20°

Q: a) Prime planes, b) Prime stresses, c) Maximum shear stress and this in the plane of the stress

A: Given data: Normal streses along x and y axis σx=12000lb/in2 σy=18000lb/in2 Shear stress…

Q: Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected…

A: Acting torque on the system = 200 ×0.15 =30 Nm Bending moment at end section = 200 ×0.25 = 50 Nm the…

Q: The state of plane stress at a point is represented by the element shown in the figure. в, - 200 Мра…

A: note: Mohr's circle is used to calculated the principle stresses

Q: Given a stress state of a, = -4 MPa, a, = 12 MPa, ty = 7 MPa cew 1) Draw a properly oriented stress…

Q: Figure 1 shows an element ith stresses. Angle 1 Tyx Tyx Figure 1 Point C)- x-direction stress…

A: The three basic equations to determine the stress at various cross-sections are:…

Q: The state of plane stress at a point is represented on the element shown in the figure. The element…

Q: Q2) An element in a plane stress is oriented at an angle 0 = 60° CCW direction. On the inclined…

A: Stress: Stress is nothing but the force per unit area. It is represented by σ. SI unit of stress is…

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: 2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m?…

Q: Q3/ Using Mohr's circle find out the principle stresses and the maximum shear stress and the stress…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: The state of plane stress at a point on the surface of a cylindrical pressure vessel is shown in…

A: A B C D E

Q: Determine the smallest allowable cross-sectional areas of each me 400 kN The working stresses are 60…

Q: Quiz// For the state of stress shown in Figure below. Draw the Mohr's circle and find the principal…

Q: (tensile), minor stress of 40 MPa (tensile) along with a counter clockwise shear stress of 30 MPa.…

Q: 2- The state of plane stress at a point with respect to the xy-axes is shown in Fig, find the normal…

A: To find : The normal and shear stress on section inclined at an angle of 30° Given : The stress in…

Q: Oy Ot Txy Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=61 MPa,…

A: Given data: Stresses on the surface of structural member σx=61 Mpa σy=32.7 Mpa τxy=-28.1 Mpa α=54.8°…

Q: [I'wo forces are applied on the beam shown below. (a) Determine the normal and shear stresses point…

A: convert lb to kN 500 lb = 2.24 kN 400 lb = 1.78 kN convert inc to mm 1 in = 25.4 mm 10 in = 254 mm…

Q: Find normal stresses and shear stress at the given inclination ..using mohr circle

Q: Consider the following plane stress state: Oх- 40 MPа, дy- 30 МРа, Тҳу— 20 MРа ссw Calculate the…

Q: Draw the Mohr's Circle (Fig. 3) as accurately as possible on a graph paper. (a) Using equation find…

Q: The stress components acting on an infinitesimal element extracted from a plate subjected to the…

A: From the given figure we can observe that the principal stress formula is given by…

Q: na stressed element, the value of normal stress along 'X' and 'Y' directions are 200 MPa (tensile)…

Q: QLESTION FOUR Demo dimensional state of stress for a point on a given structural component is given…

Q: Find the Normal Stress at points A, B, and C

A: To Find the Normal Stress at points A, B, and C

Q: The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane…

A: (a) To find: The principle stress. Given: The stress in x-direction is σx=-85 MPa. The stress in…

Q: The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz =…

A: given; σx=120MPaσy=55MPaaσZ=-85MPaσxy=-55MPaσxz=-75MPaσyz=33MPa

Q: 10 MPa 9. Using Mohr's circle, for the figure at the right, determine: a) The angle to the principal…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPª لاخرين 24 1 10 2 20 МРа…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: Oy Ot Txy Tnt Ox On n (b) (a) On the surface of a structural member, stresses are given as ox=67,9…

A: The stress stress after rotation is given by - τnt=-σx-σy2sin2α + τxycos2α In first case-…

Q: In the following Figure using given material properties. a) Determine the internal forces and…

A: Thermal strain in a material occurs when there is a change in the temperature of the substance. The…

Q: find the principal stress , maximum in plane shear stress

Q: Two perpendicular tensile stresses of 300 MPa and 150 MPa act at a point in a material. Draw the…

Q: (a) The plane stress at a point with respect to x-y-axes is shown in Fig. Q1(a). By using…

A: according to the given details:

Question

ı need solution

as given below
80 mm
a) Normal and shear stresses
occurring at point A
Find and show it on the plane
stress element.
b) Find the principal stresses and
the maximum shear stress
diameter
=20mm
120 mm
occurring at point A with their
planes.
SKN
70mm
TKN
2kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the xy axes, that is, determine crv, tr(_, and t. Show the results on a sketch of an clement oriented at B = 10
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
At a point in an elastic material under strain, the stresses on the three mutually perpendicular planes are as follows:A normal tensile stress of 60 N/mm^2and shear stress of 40 N/mm2 on one plane and a normal tensile force of 40 N/mm^2and a complimentary shear stress of 40 N/mm^2 on another plane. Find the following using Mohr circle only (take 5 N/mm2 = 1 cm)a. The principal stresses and principal planes.b. The maximum shear stress and its plane.c. The normal and shear stress on a plane inclined at an angle of 30Oto major principal plane.
a) Prime planes,b) Prime stresses, c) Maximum shear stress and thisin the plane of the stressdetermine the normal stress