Answered: A beam of rectangular section of 12 cm…

A beam of rectangular section of 12 cm × 20 cm is simply supported over a span of 12 m. It is acted upon by a load of 80 kN at the mid span. Determine the maximum bending stress induced in thr beam.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.13.4P: A rectangular beam with semicircular notches, as shown in part b of the figure, has dimensions h =...

See similar textbooks

Related questions

Q: A beam is subjected to equal bending moments of M, = 52 kip-ft. The cross-sectional dimensions are…

Q: The beam shown has an second moment of area of 9,500,000 mm4 and a controlling section modulus of…

Q: 3. A beam with a maximum moment of 20kN-m has a height of 20mm and a width of 15mm. Determine the…

Q: Draw the shear and bending-moment diagrams for the beam and loading shown and determine the…

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

A: Given-Data:- AB=3m dindout=13 Bending stress=110N/mm2 Average shear stress=15N/mm2 To-Find:- 1)…

Q: A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 644 lb as shown. The…

Q: A 8-kN load is supported by a cart that rolls along a beam as shown in Fig. Show that the maximum…

A: Draw the free-body diagram of the beam.

Q: Flexural Members The cross-sectional dimensions of a beam are given. If the maximum allowable…

A: Given Data: Maximum bending stress, 230 MPa

Q: A picture is taken of a man performing a pole vault, and the minimum radius of curvature of the pole…

A: Given, The radius of curvature = 4.5m = 4500 mm Diameter of pole = 40 mm Young’s Modulus = 131 GPa…

Q: The steel beam has the cross section shown. The beam length is L= 19 ft, and the cross-sectional…

Q: A beam is subjected to equal 19.1 kip-ft bending moments. Assume ty = t2 = ty= 1 in., d = 10 in, by=…

Q: Flexural Members A simply supported wood beam having a length of 24 ft and rectangular in cross…

Q: An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm…

A: Given data : maximum bending stress () = 40 MN/m2 thickness of flange(tf) = 25 mm thickness of web…

Q: A simply supported wood beam with a span of L = 24 ft supports a uniformly distributed load of wo =…

A: Given: The length of the beam, L = 24 ft The intensity of load, wo = 350 lb/ft The maximum bending…

Q: For the beam and loading shown, determine the maximum bending stress on a transverse section at C.…

Q: Determine (a) the distance a for which the maximum absolute value of the bending moment in the beam…

A: Given data To determine a) the distance a for which the maximum absolute value of the bending…

Q: I₂ = 18×106 mm¹ 2.40 m 23.20 kN-m 180.00 mm 1 For the beam and cross section shown, compl maximum…

A: GivenM=23.20 kNm=23.20×106 NmmIz=18×106 mm4y¯1=180mmy¯2=120mm

Q: A simply supported wood beam with a span of L=12 ft supports a uniformly distributed load w. The…

Q: For the beam and loading shown, draw the shear force and bending moment diagrams of the beam AC.…

A: The free-body diagram of the beam is given as, In this diagram, 2 kN load is displaced at point C…

Q: From the beam shown, determine the maximum shear stress and maximum bending moment. 150 N| 250 N|…

A: Consider horizontal forward & vertically upward force as (+)ve and vertically downward force as…

Q: A 20 m long beam is simply supported at the left end and 5m from the right end. It is to be used as…

Q: The structure shown below consists of a brass core inserted into a steel tube of cross section…

Q: A concentrated load of 6.24 KN is appliled at the free end of a caotilever wooden beam consisting of…

Q: The simply supported beam of rectangular cross section carries a distributed load of intensity w0 ¼…

Q: Question 77 A light-alloy beam (i.e., assume weightless beam) has a solid rectangular homogeneous…

Q: of the beam are breadth, b = 35 mm and depth d = 125 mm. Calculate the maximum bending stress and…

Q: Determine the maximum bending moment for the beam shown below. Use a = 8 ft, b = 12 ft, c = 6 ft,…

Q: A simply supported wood beam with a span of L = 14 ft supports a uniformly distributed load w. The…

Q: A pair of lock gates are strengthened by two girders AC and BC. If the load on each girder amounts…

A: Please find the answer below

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

Q: times larger than in stee Q1) For the section shown aside, if the bending stress at point B is 225…

A: Given:- Bending stress at pont B, σB=225 MPaTo find:-Maximum bending stress, σmax

Q: The ratio of bending stresses induced beams, which have section modulus of 100 mm3 and 300 mm3…

Q: A pair of lock gates are strengthened by two girders AC and BC. If the load on each. girder amounts…

A: In the above question it can be clearly seen that at the contact point of the two girders, there…

Q: A composite T-beam whose cross-section is shown below is constructed by bonding together of a steel…

A: When beams are subjected to loading they experience bending moment which tends to bend the beam in a…

Q: Problem 1 of 1: Determine the nodal solution and maximum 70 Iblin bending moment in the beam, if E =…

A: R1 + R2 + R3 = 12 ( 70 ×(18×12)) = 7560 lb

Q: A non-symmetrical I beam is loaded by the moment shown. Determine the maximum bending stress. 1 in.…

Q: 3 kN/m |6.0 kN 1 kN/m A B 500 mm 0.5 m 000 1.0 m→1.0 m→ 2.0 m- -4.0 m 200 mm

Q: A 30 kN/m HII IL C -1.8 m- -1.8 m- D 000 24 KN BI 0.6 m W200 X 46.1

Q: 8 ft The cantilevered beam above is subjected to a single point force P = 20 kip at its free end.…

Q: Determine the maximum bending moment magnitude for the beam shown below. Use a = 21 ft, b = 8 ft,…

A: Given Data: The magnitude of UDL load, w=6 kips/ft

Q: Determine the maximum bending moment magnitude for the beam shown below. Use a = 20 ft, b = 7 ft,…

Q: A timber dam is made of planking backed by vertical piles. The piles are built-in at the section A…

A: We have given

Q: A beam is simply supported on a span of 10 m. The beam supports a load of 15 kN/m on its entire…

A: Given Data: Length of the beam, L=10 m The magnitude of UDL load, w=15 kN/m Maximum bending stress,…

Q: Hwi A beam with I cross-Section is Subjected to negative bending moment M: 50 KN.m.The Cross…

Q: A Circular cross -Sectional beam of diameter 200 m, Simply Supported at both ends and loaded as…

Q: A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are…

Q: For the beam shown, with the maximum moment and section modulus of its cross-section as reference. 8…

Q: Determine the maximum bending stress in a cantilever beam of length 20 m. The beam is subjected to a…

A: For beams under given loading condition, bending equation gives the relation between the radius of…

Question

A beam of rectangular section of 12 cm × 20 cm is simply supported over a span of 12 m. It is acted upon by a load of 80 kN at the mid span. Determine the maximum bending stress induced in thr beam.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular beam 80 mm x 40 mm is 3m long and simply supported at the ends. It carries a load of 1 kN at the mid-span. Determine the maximum bending stress induced in the beam.
Determine the most critical point of the beam shown below in terms of bending moment.
An I section symmetrical beamhas 200mm wide flange and overall depth of 500mm. Each flange is 25mm thickand the web is 20mm thick. Determine the maximum bending moment that should be imposed in the sectionif the tensile or the compressive stressis not to exceed 40MN/m^2 and what percentage of the moment is resisted by flange or web?
A picture is taken of a man performing a pole vault, and the minimum radius of curvature of the pole is estimated by measurement to be 4.5 m. If the pole is 40 mm in diameter and it is made of a glass-reinforced plastic for which Eg = 131 GPa, determine the maximum bending stress in the pole.
A solid steel shaft, circular in cross section, has a change in diameter from 135 mm to 90 mm with a fillet radius of 4.5 mm at the place of change. A load with a bending moment of 1500 N-m is applied in the shaft at the cross-section change. Determine the maximum bending stress induced in the shaft at the cross-section cha
Draw the shear stress diagram and bending moment diagram for a beam with the free body diagram shown below. Identify the location of critical point(s) in the beam. Given AB = 0.5 m, BC = 0.6 mm, and CD = 0.5 m.
A load of 100 kN, followed by another load of 50 kN, at a distance of 10 metres, advances across a girder with a 100-metre span. Obtain an expression for the maximum bending moment at a section of the girder at a distance of z metres from an abutment. Please provide solutions. Answer is z(140-1.5z) for z< (100/3)m;(100-z)(1.5z-5) for z>(100/3) m.
A beam is subjected to equal bending moments of Mz = 44 kip·ft. The cross-sectional dimensions are b1 = 6.5 in., d1 = 1.5 in., b2 = 0.90 in., d2 = 6.2 in., b3 = 2.6 in., and d3 = 1.8 in. Determine:(a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis.(b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative.(c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative.(d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
Determine the maximum bending stress in a cantilever beam of length 20 m. The beam is subjected to a point load at its free end and the diameter of the beam is 40 mm and elastic constant is 160 Gpa.
A simply supported beam AB = 11 m has a hollow rectangular cross-section with 13 cm as width, 22 cm as depth and inner thickness as 2 cm is subjected to a point load of 9 N & 6 N acting at C and D respectively and a uniformly distributed load (UDL) of 9 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
A solid beam supported on bearings 15 ft apart, has a cross-section of 1/2 in deep and 3/8 in wide. Determine the bending stress in the beam assuming that a load of 10 lbis applied gradually at the center of the beam length.
A horizontal beam under bending has a maximum bending stress of 100 MpA and a maximum shear stress of 20 Mpa. What is the maximum principal stress induced in the beam.