Draw the shear and bending-moment diagrams for the beam and loading shown and determine the magnitude of the maximum normal stress due to bending. la| (max)= 15 ksi 5 kips/ft 10 kips-ft 9 in. 3 in. 9 ft 7 ft--| Check Answer for this Problem Close

Q: Which one of the following instruments is wide used to check and calibrate geometric features of…

A: Which one of the following instruments is widelyused to check and calibrate geometric features…

Q: R= 0.2 m 13.15 The rate of change of speed of the belt is given by 0.06(10 – t) m/s², where t is in…

A:

Q: What is the principle of operation of a rice combine harvester?

A:

Q: the bracket must support the four forces shown in figure. the magnitude of the resultant force is:

A:

Q: Is it possible for the internal reaction force in a truss to exceed that applied on the system of…

A: Given Truss To find The internal resistance forces are greater than applied force

Q: 3. At a section in & propetties are Known. Po = 1000 KPa; To=500k ; V= 200 m/ec %3D é) The…

A: Given Data The initial temperature is:To=500 K The initial pressure is:Po=1000 kPa The velocity…

Q: Explain mist type lubrication system, write its advantages and disadvantage?

A: Lubrication system: IC motor is made of many complex components. Because of consistent development…

Q: An Otto cycle operates on 1lb/s of air from 15 psia and 130 F at the beginning of compression. The…

A:

Q: tionary when the force F is first applied, determine the upward velocity of the supported mass after…

A:

Q: Two airplanes are performing at an air show. Plane A travels along the path shown and, for the…

A:

Q: At the lowest and highest points on its trajectory, the pendulum cord, with a length L = 2 ft, forms…

A:

Q: Calculate the pressure difference between points A and B for the differential manometer below. Oil…

A:

Q: Suppose potential p in millivolts is given by the expression p = k(x3 - x) where x is in cm and k in…

A:

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

A:

Q: 2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air…

A:

Q: The 15-kg block is subjected to the force shown. Determine its velocity at s= 4m if v= 6 m/s at s=0.…

A: It is very basic question of mechanics. Used concept is Newton's second law of motion.

Q: Exercise 1.3. Extend the upper bound on the number of collisions to a wedge convex inside; see…

A: Turning a key in a lock is a recognizable encounter. Envision a "key" that is a chamber with curved…

Q: The resultant of two forces acting at a point at right angles to each other is 240 pounds. Determine…

A:

Q: A particle moves along the x-axis such that its coordinates (x) varies with time (t) according to…

A:

Q: A fluid is weighted in a laboratory. It is found that 6 LITERS of the fluid weight 37 N. What is the…

A: Given:Volume of the fluid, V=6 liters or 0.006 m3fluid weight, w=37 N

Q: Determine the magnitude and sense (cw or ccw) of the resultant moment produces by the force system…

A: Find the magnitude and sense of the resultant moment about point O.

Q: Blocks A and B are released from rest in the position shown. Neglecting friction, the normal force…

A:

Q: 6-105. The member has a square cross section and is subjected to a resultant internal bending moment…

A:

Q: What is the Maximum/minimum point on the curve of Moment Diagram.

A: Moment diagram is the diagram obtained by using bending moment at each point of structure.

Q: In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480 deg. C. The condenser is at 32 deg.…

A: Given data Condition of steam entering the turbineP1 = 4.1 MPa = 41 barT1 = 480 °CCondenser…

Q: In a piping network system, the volume flow rates (gallon per minute) in four different pipes are…

A: The system of equations are as follows. -3Q1+ 2Q2+5Q3+1Q4=15.5______________Equation (1) 2Q1+…

Q: In the figure shown, if wa=500rpm , solve for (a) the angular velocity of disk C (in rad/s) (b) the…

A:

Q: Two vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m.…

A:

Q: A rigid tank whose volume is unknown is divided into two parts by a partition. One side of the tank…

A: Answer: The final temperature of the gas is 3327℃.

Q: Given the following vectors: S = 3i - j+ 5k P = 2i + 4j - 6k %3D Q = -7i + 2j + 9k %3D Obtain the…

A:

Q: In the figure shown, If v=700 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular…

A:

Q: 30° 40° 45° 80 lb 150 lb 120 lb Using summation of forces, calculate for R and angle. Make sure to…

A:

Q: For the mechanical translation system below, find the transfer function 01/T and 02/T. Use the…

A:

Q: Specify the pump type that would be used for the following conditions: N = 675 rpm; Q = 20 000 gpm;…

A: Given       Speed, N = 675 rpm Discharge, Q = 20000 gpm                      = 1.26 m3/s…

Q: 20. The young’s modulus of nickel is 209 gpa. Determine the length of the bar (in mm) when a force…

A:

Q: Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds…

A: Write the expression of velocity of flow through the smooth horizontal pipe. v=vmax1-r2R2

Q: 4. Compute for the reaction at the roller B, the force components acting on the ball- and-socket at…

A: Find the reaction at A and B and also find the value of T.

Q: 2. Bar AB is rotating in the counterclockwise direction at 5 rad/s. The disk rolls on the horizontal…

A:

Q: 1. Each of the four vertical links has a 8 x 36-mm uniform rectangular cross section and each of the…

A: Given:The cross-section area of each vertical four links, A = 8 mm x 36 mmThe diameter of each pin,…

Q: Calculate the pressure difference between P1 and P2. The specific gravity of mercury is 13.6 and…

A: GivenSGhg=13.6SGgl=1.26

Q: analytical and graphical solution of the forces

A: Given BA=5.755kN strut, this means it is -ve CA=4.317kN tie

Q: Q4/ Assuming the car has no dependence on friction with the road, determine the speed u of the car.…

A: Given:Coefficient of static friction, μ=0.8θ=40or=365 m

Q: Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a…

A: Given data

Q: A house is cooled by a heat pump driven by an electric motor using the inside as the low-temperature…

A:

Q: The disk rolls without sliding on the fixed horizontal surface. At the instant shown, the…

A:

Q: For a case of plane stress, oy = 40MN/m2, Oy = 0, txy = 80MN/ m2. What are the principal %3D…

A:

Q: 19. Find the maximum force (kN) that a 2.5 mm thick and 50 mm wide nickel strip, having a yield…

A: Answer: A force which is less than 38.75 kN can withstand with no plastic deformation.

Q: 100 min J00 mf 1- Determine the shear stress at points A and B on the beam if it is subjected to a…

A:

Q: 20 cm in size if the thermal contact conductance on both sides of the copper plate is estimated to…

A:

Q: expression p = K(x - x) where x is in cm and k in mV-cm. a. Find the divergence of p for k=1/2…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.