A blimp is designed to move in air at "C at 7 m/s. If a 1:20 scale model is tested in water at 20 °C, what should the water velocity be? If the measured water drag on the model is 3.2kN, calculate the drag on the prototype blimp and the power required to propel it. (For water u 1.02x10 pa.s, p 1000 kg/m' and for air u 1.81x10 pa.s, p- 1.2kg/m')

A blimp is designed to move in air at "C at 7 m/s. If a 1:20 scale model is tested in water at 20 °C, what should the water velocity be? If the measured water drag on the model is 3.2kN, calculate the drag on the prototype blimp and the power required to propel it. (For water u 1.02x10 pa.s, p 1000 kg/m' and for air u 1.81x10 pa.s, p- 1.2kg/m')

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A road haulage truck has an approximate rectangular frontal area 2.5 m wide by 3.8 m high. To investigate the drag on the truck, a one – fifth scale model is to be tested in a wind tunnel. We can assume that the density and viscosity of the air are the same for the model as for the full size truck. If the truck travels at 120 km/h, what is the appropriate air speed for the model in the wind tunnel?
A 1:20 scaled-down model of a hydrofoil is tested in a water channel, at a velocity of 0.179 m/s. At this velocity, a drag force of 2.2 N is measured. Determine the drag force of the original hydrofoil, at a velocity of 0.8 m/s.
a test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. Evaluate: a) the speed of the model take the number of froud into account in your analysis.
a test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. Evaluate: a) the speed of the modelb) the ratio between the drag forces of the model and the prototypec) the relationship between the powers needed to overcome the drag of the model and the prototype take the number of froud into account in your analysis.
Fluid Mechanics Problem: A ship is 150 m long and has a wetted area of 5000 m2.If it is encrusted with barnacles, the ship requires 7000 hp to overcome friction drag when moving in seawater at 15 kn and 20oC. What is the average roughness of the barnacles? How fast would the ship move with the same power if the surface were smooth? Neglect wave drag. Note: Treat the ship hull as a flat plate. Use eq. 7.48b to find effective barnacle roughness height.Use equation (7.45) White for the drag coefficient CD = D/.5pV2A , where A is the hull (plate) area, to find the ship velocity for smooth plate.
The parachute in the chapter-opener photo is, of course,meant to decelerate the payload on Mars. The wind tunneltest gave a drag coefficient of about 1.1, based upon theprojected area of the parachute. Suppose it was falling onearth and, at an altitude of 1000 m, showed a steady descentrate of about 18 mi/h. Estimate the weight of the payload.
2) A prototype ship is 50 m long and designed for cruising speed of 10 m/s. The drag is to be simulatedby a 1-m-long model that will be towed in a towing tank. Using Froude scaling, determine the tow speedand the ratio of the model to prototype drag and power.
A diamond-shaped body, of characteristic length 9 in, hasthe following measured drag forces when placed in a windthe tunnel at sea-level standard conditions: Use these data to predict the drag force of a similar 15 - indiamond placed at similar orientation in 20 ° C water flowingat 2.2 m/s.
a test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. a) model speed b) the ratio between model and prototype drag windows c) a ratio between the powers needed to overcome the drag of the model and the prototype take the number of froud into account in your analysis.
A student needs to measure the drag on a prototype of characteristicdimension d p moving at velocity U p in air at standardatmospheric conditions. He constructs a model ofcharacteristic dimension d m , such that the ratio d p / d m issome factor f . He then measures the drag on the model atdynamically similar conditions (also with air at standardatmospheric conditions). The student claims that the dragforce on the prototype will be identical to that measured onthe model. Is this claim correct? Explain.
Some engineers want a good estimate of drag and boundary-layerthickness at the trailing edge of a miniature wing. The chord and span ofthe wing are 6 mm and 30 mm, respectively and a typical flight speed is5 m/s in air (kinematic viscosity = 15 × 10−6 m2/s; density = 1.2kg/m3). An engineer may decide to make a superseding model withchord and span of 150 mm and 750 mm, respectively. Measurements onthe model in a water channel flowing at 0.5 m/s (kinematic viscosity = 1× 10−6 m2/s, density = 1000 kg/m3) give a drag of 0.19 N and aboundary-layer thickness of 3 mm. Estimate the corresponding values forthe prototype
A beach ball 20 cm in diameter traveling at a speed of 50 m/s in still air at 30°C is found to have a drag of 8 N. (a) Find the velocity at which the drag of a 60 cm sphere immersed in water at 15°C can be found from the above data. (b) What is the drag of the larger sphere at this velocity?